ap--/python-seabreeze

Issues

• QE Pro -- data transfer error

  #123 opened 3 years ago
  1

• Module not using sensitivity calibration

  #122 opened 3 years ago
  3

• Getting temperature of FLAMES Spectrometer

  #119 opened 3 years ago
  8

• Ocean Optics Multi-Channel Spectrometry Oddities

  #116 opened 4 years ago
  1

• usb.core.USBError: [Errno 13] Access denied (insufficient permissions)

  #115 opened 4 years ago
  4

• Warning message in seabreeze_os_setup should state that it's a known error

  #114 opened 4 years ago
  4

• maya2000 driver issue

  #113 opened 4 years ago
  2

• ADC1000-USB with SD2000 not detected

  #112 opened 2 years ago
  5

• docs for installing python-seabreeze without cseabreeze need fixing

  #111 opened 4 years ago
  5

• QE65000 integration_time_micros does not block until complete in cseabreeze?

  #110 opened 4 years ago
  10

• pyseabreeze: OBPProtocol.receive docstring is incorrect

  #109 opened 4 years ago
  1

• FLAME-T Hangs when switching back from trigger modes

  #108 opened 4 years ago
  12

• Calibration

  #107 opened 4 years ago
  2

• Problem using Single Strobe on spectrometer Flame

  #106 opened 4 years ago
  0

• supported device

  #105 opened 4 years ago
  6

• intensities value from USB4000

  #104 opened 4 years ago
  5

• Flame-S spectrometer readout timing issues

  #102 opened 4 years ago
  2

• SeaBreezeError: allow isinstance tests between backends

  #101 opened 4 years ago
  0

• Calling seabreeze.use after importing seabreeze.spectrometers does not throw warning

  #100 opened 4 years ago
  3

• seabreeze_os_setup windows issues

  #99 opened 4 years ago
  0

• Flame-S Edge Trigger Mode and Timing

  #97 opened 4 years ago
  29

• minimum integration time

  #96 opened 4 years ago
  4

• Ocean FX | Integration Time Error: Input was out of bounds

  #94 opened 4 years ago
  3

• Flame-S spectrometer is seen but doesn't report data

  #92 opened 4 years ago
  15

• Refactor tests to run for each backend independently

  #91 opened 4 years ago
  6

• Correcting dark counts results into ValueError when using pyseabreeze backend.

  #90 opened 5 years ago
  1

• Integration time max not correct (pyseabreeze, USB4000 / FLAME-T)

  #89 opened 5 years ago
  1

• Dark pixel indices discrepancy (USB4000 / FLAME-T)

  #88 opened 5 years ago
  3

• spec.intensities() does not work (pyseabreeze with FLAME-T / USB4000)

  #87 opened 5 years ago
  12

• using `list_devices()` closes currently opened devices

  #86 opened 5 years ago
  9

• usb_raw_write/read

  #85 opened 5 years ago
  3

• installing seabreeze without cseabreeze backend instructions broken

  #84 opened 5 years ago
  2

• q

  #83 opened 5 years ago
  1

• pyseabreeze features implementation

  #81 opened 5 years ago
  5

• Reading temperature from the spectrometer temperature sensor

  #80 opened 5 years ago
  4

• Functionality to write eeprom data.

  #79 opened 5 years ago
  2

• udev rules not applied when spectrometer is already connected before boot

  #78 opened 5 years ago
  6

• Driver version compatibility?

  #77 opened 5 years ago
  2

• seabreeze_setup_os does not run

  #76 opened 4 years ago
  7

• how to set_scans_to_average via .f or .feature

  #75 opened 5 years ago
  1

• correct_nonlinearity=True gives incorrect intensities

  #74 opened 5 years ago
  4

• How to get absorbance

  #73 opened 5 years ago
  1

• pyseabreeze backend broken for HR4000

  #72 opened 5 years ago
  0

• docs: add note recommending to not pip install in conda env

  #71 opened 5 years ago
  0

• tests: add timeout to pytests

  #70 opened 4 years ago
  1

• HR4000 returning data transfer error

  #69 opened 5 years ago
  7

• Need help implementing new methods

  #68 opened 5 years ago
  2

• Implement getMaximumIntensity()

  #67 opened 5 years ago
  1

• Udev rules does not work on Raspberry Pi 3

  #66 opened 5 years ago
  4

• No Devices Found, Possible issue with driver

  #65 opened 5 years ago
  2