Pinned Repositories
avdweb_pedelec_legalisation_device
Eagle-library-addressable-LED-rings
Eagle library for easily create addressable LED rings NeoPixel WS2812B-2020
PCB-Spotwelder-Controller
SAM-15x15
SAM15x15
SAM15x15 board / Arduino Zero package which describes all SAMD21G pins
Spotwelder
Spotwelder-controller
avdweb_FreqPeriodCounter
Smart library with comprehensive functions for counting (multiple) frequencies and period-times. For Arduino Uno and Zero.
wrapper_Fast-PWM-DAC-SAMD21
Fast PWM-DAC library for the SAMD21 and Arduino Zero
wrapper_SAMDtimer
SAMD21 Timer library for the SAM15x15 and Arduino Zero
avandalen's Repositories
avandalen/SAM-15x15
avandalen/Spotwelder-controller
avandalen/PCB-Spotwelder-Controller
avandalen/Eagle-library-addressable-LED-rings
Eagle library for easily create addressable LED rings NeoPixel WS2812B-2020
avandalen/SAM15x15
SAM15x15 board / Arduino Zero package which describes all SAMD21G pins
avandalen/avdweb_pedelec_legalisation_device
avandalen/Spotwelder
avandalen/Connectorless-zigzag-1x6-mini-ISP-connector
An Arduino ISP connector is used, among others, for burning a bootloader and for programming ATtiny chips. When the ISP connector is only used once, it would be more convenient not to use a connector. Therefore, I created the connectorless 1x6 mini ISP connector and the mini 1x6 ISP adapter. By the zigzag positions of the PCB holes, the male ISP connector pins press against the holes and make electrical contact and so, no PCB connector is needed.
avandalen/MH-M38-Bluetooth-audio-receiver-schematic
avandalen/Simulation-e-bike-hub-and-mid-drive-motor-efficiency-vs-speed
Here we can simulate an e-bike with a hub motor or mid-drive motor in all situations. Also, a mid-drive motor can be tested at a constant cadence / bottom bracket speed.
avandalen/Changing-Arduino-IDE-theme-colors
Changing the Arduino IDE tab and comment font colors
avandalen/Reflow-oven
Reflow oven software written in Arduino IDE for Avdweb UPC control board
avandalen/Daytime-running-light-for-ebikes
avandalen/FDTI-UPDI-connector
Typically, debugging via the serial monitor and burning the bootloader requires 2 connectors: FTDI For debugging and uploading the sketch UPDI For burning the boot loader (like the ICSP connector for the Atmega328 and others) These connectors, however, take up a lot of space on the pcb, especially with respect to the fact that the ATtiny devices, such as the ATtiny3217, are very small. That is why I have designed a new combined FTDI / UPDI connector, which take less space on the pcb.
avandalen/Rain-sensor-for-Somfy-motorized-awning
avandalen/Solarcell-curve-tracer
avandalen/Bontrager-Ion-200-RT-holder
Freecad 3d CAD model for the Bontrager Ion 200 RT holder
avandalen/CR6842S-flyback-converter
avandalen/cubesat_eps
avandalen/DIY-e-bike-thumb-throttle-switch
avandalen/Electronic-larynx
avandalen/Hammond-1591XXSGY-frontpanel
avandalen/megaTinyCore
Arduino core for the new megaAVR ATtiny series chips
avandalen/QC3Control
Set the voltage of a Quick Charge 3.0 source via the Arduino.
avandalen/SAM15x15-production-test
avandalen/SerialUPDI-Programmer
Burning a bootloader into the ATtiny3217 with the SerialUPDI Programmer