bbogush/nand_programmer

Issues

• Will support for writing SPI NAND still be updated?

  #80 opened 2 months ago by v6760hu
  2

• 准备把nando用STM32CubeMX和STM32CubeIDE移植到STM32F407VET6的HAL库上。bootloader和app的cdc驱动已做好了。有兴趣可以一起加入

  #76 opened 8 months ago by whitcloudfly
  5

• 将上位机的功能通过增加触摸屏和TF卡存储实现脱机烧写，以STM32F407VET6的资源是否可行。

  #81 opened a month ago by whitcloudfly
  0

• Can you add MT29F4G16ABBD?

  #79 opened 6 months ago by rudolf992
  1

• NANDO Eagle PCB (48pin ZIF)

  #41 opened 3 years ago by kooroshi60
  9

• 上位机闪退

  #68 opened a year ago by v6760hu
  1

• Issue with EN25F80-75HCP

  #71 opened 8 months ago by kooroshi60
  2

• Can you share how to add SPI NAND and add particle teaching library

  #72 opened 8 months ago by v6760hu
  1

• add NAND Micron 29F1G08ABADA

  #70 opened 8 months ago by web-rpi
  2

• Does Huabang Winbond's spi nand not support it

  #73 opened 8 months ago by v6760hu
  0

• Can this support SPI nand flash?

  #69 opened 10 months ago by CharlesJin6
  0

• 可以弄个GD32F103VCT6 的固件吗 STM32F103VCT6 快

  #64 opened a year ago by v6760hu
  2

• Bad blocks addresses and size mismatch when reading BBT and writing flash

  #67 opened a year ago by patryk-pe
  0

• If using stm32f407vet6 as the main control

  #66 opened a year ago by v6760hu
  0

• Question about building firmware

  #65 opened a year ago by loki-amorf
  1

• Parallel NOR flash support?

  #37 opened a year ago by donnm
  4

• Porting programmer to raspberry

  #38 opened a year ago by hamid1920
  1

• Does it support GD32F103VCT6?

  #53 opened a year ago by myseil
  10

• Hangs 3.5.0

  #63 opened a year ago by Sana956
  1

• Is K9F1G08U0D supported?

  #59 opened a year ago by hpznot
  6

• K9K2G08U0M SLC Die Stack series support

  #60 opened a year ago by loki-amorf
  1

• Porting to stm32F407 series?

  #57 opened a year ago by deividAlfa
  1

• Gg

  #51 opened a year ago by Dusjelis
  0

• is it possible to erase by block instead of full chip erase?

  #27 opened a year ago by danyhm
  6

• TC58BVG0S3HTA00

  #61 opened a year ago by Sana956
  0

• Some UI/UX suggestions

  #30 opened 3 years ago
  8

• The crystal isn't same.

  #56 opened a year ago by hpznot
  4

• Can particle ID be read

  #50 opened a year ago by kane-abbe
  0

• Larger font required

  #49 opened 2 years ago by kane-abbe
  1

• NAND128-A/NAND256-A/NAND512-A/NAND01G-A: unsupported read command style

  #31 opened 2 years ago
  2

• Is it possible to support rebuild Bad Block Table ?

  #42 opened 2 years ago by hpo14
  1

• EN25Q32B 4Mbyte SPI flash issue

  #44 opened 2 years ago by kooroshi60
  4

• More NAND - more pleasure

  #45 opened 2 years ago by Demiurge67
  0

• Support for larger NAND chips?

  #46 opened 2 years ago by 7134956
  9

• Wrong timing calculation code?

  #47 opened 2 years ago by 7134956
  1

• Operation address exceeded chip size

  #43 opened 3 years ago by hpo14
  2

• TSOP56 NAND Compatibility

  #40 opened 3 years ago by kooroshi60
  2

• Page address offset calculation (Add new SPI chip)

  #39 opened 3 years ago by kooroshi60
  1

• Replace R3, R13, R14 with lower value resistors

  #36 opened 3 years ago by donnm
  1

• Fix S34ML0xG1 names in chip db

  #34 opened 3 years ago by donnm
  1

• Fix ASCII typo (?) in GUI

  #35 opened 3 years ago by donnm
  1

• Add support for K9G8G08U0M

  #33 opened 3 years ago by donnm
  1

• Potential issues on bad block handling

  #32 opened 3 years ago
  1

• How to flash firmware using usb serial cable?

  #24 opened 3 years ago by Retro-Fitt
  65

• Does it support STM32F407?

  #26 opened 3 years ago by quanghau113
  4

• The Qt host application will not compile on gcc9 and newer

  #29 opened 3 years ago
  1

• Can you add support for STM32F103ZET6

  #23 opened 3 years ago by mlpzaq9998
  9

• Can you add support for stm32 blue pill ?

  #25 opened 3 years ago by ellisonmax
  0

• Reset pad

  #18 opened 4 years ago by alexgrach
  6

• Error detecting TC58NVG1S3E

  #17 opened 4 years ago by alexgrach
  3