/ROS_quadrotor_simulator

Quadrotor simulator using ROS, Gazebo, and RVIZ

Primary LanguageC++

ROS Quadrotor Simulator

This project focuses on simulating a quadrotor aerial vehicle for the development of flight control systems, autonomous navigation, obstacle avoidance, and path planning. This software relies on the Robot Operating System (ROS) software. ROS provides hardware abstraction, device drivers, libraries, visualizers, message-passing, package management, and more. Along with ROS, Gazebo is used for simulation. Gazebo offers the ability to accurately and efficiently simulate populations of robots in complex indoor and outdoor environments.

This project begins with simple manual control of the quadrotor with an Xbox joystick. It then evolves to simulating GPS waypoint navigation. Once the quadrotor can follow a series of waypoints, it is possible to develop 2D and 3D maps of the environment. These maps are used for 2D and 3D path planning and obstacle avoidance.

Detailed instructions and images describing the installation and utilization of this software is available at https://www.wilselby.com/research/ros-integration/

This software package contains several modules, described below:

  • action_controller - A simple action controller to translate the trajectory produced from MoveIt! into a velocity command for the quadrotor for 3D navigation
  • moveit_simple_controller_manager - A modified version of Moveit_simple_controller_manager to handle a multi degree of freedom trajectory for 3D navigation
  • quad_2dnav - Package to enable 2D map generation and 2D navigation using the Navigation stack
  • quad_3dnav - Package to enable 3D map generation and 2D navigation using MoveIt!
  • quad_control - Nodes for the attitude and position controllers as well as a waypoint publisher node
  • quad_description - Files to support the quadrotor model required for Gazebo simulation
  • quad_gazebo - Launch files and world files required for Gazebo simulation
  • quad_joystick_interface - Package to interface with an Xbox controller to manually control the quadrotor

Getting Started

These instructions will cover the installation of ROS, Gazebo, and several other basic packages required for this software to run. This is a modified version of the scripts provided here https://github.com/AurelienRoy/ardupilot_sitl_ros_tutorial

This first section installs ROS, and a few additional dependencies and compiled packages required for the Ardupilot simulation.

Install ROS and primary pacakges

$ sudo sh -c 'echo "deb http://packages.ros.org/ros/ubuntu $(lsb_release -sc) main" > /etc/apt/sources.list.d/ros-latest.list'
$ sudo apt-key adv --keyserver hkp://pool.sks-keyservers.net --recv-key 0xB01FA116
$ sudo apt-get update

In case there was a missing dependency, you may try the following line. However, be careful not to attempt to desinstall-reinstall libgl1-mesa,for it sometimes messes up the ubuntu installation.

$ sudo apt-get -y install libgl1-mesa-dev-lts-utopic

Install ROS Indigo

$ sudo apt-get -y install ros-indigo-desktop-full
$ sudo rosdep init
$ rosdep update

Setup environment variables

$ sudo sh -c 'echo "source /opt/ros/indigo/setup.bash" >> ~/.bashrc'
$ source ~/.bashrc

Get rosinstall and some additional dependencies

$ sudo apt-get -y install python-rosinstall          \
                        ros-indigo-octomap-msgs    \
                        ros-indigo-joy             \
                        ros-indigo-geodesy         \
                        ros-indigo-octomap-ros     \
			            unzip

If Gazebo 4.x was installed, it can simply be removed with the following commands:

$ sudo apt-get remove gazebo4
$ sudo apt-get install libsdformat1
$ sudo apt-get install gazebo2

Additional Gazebo models can be downloaded from the OSRF repository (https://bitbucket.org/osrf/gazebo_models) and placed into the default Gazebo worlds folder for offline use

Install mavros but from shadow repo to get latest version earlier

$ sudo sh -c 'echo "deb http://packages.ros.org/ros-shadow-fixed/ubuntu/ $(lsb_release -sc) main" > /etc/apt/sources.list.d/ros-shadow.list'
$ sudo apt-get update
$ sudo apt-get -y install ros-indigo-mavros \
			            ros-indigo-mavros-extras

Create the catkin workspace

This next section creates a ROS workspace and fetch source repositories, placing them in the directory:

/home/<user>/ros/catkin_ws

Feel free to modify the destination path for the ROS workspace:

$ WORKSPACE=~/ros/catkin_ws
$ source ~/.bashrc

Setup the workspace

$ mkdir -p $WORKSPACE/src
$ cd $WORKSPACE/src
$ catkin_init_workspace
$ cd $WORKSPACE
$ catkin_make
$ sh -c "echo 'source $WORKSPACE/devel/setup.bash' >> ~/.bashrc"

Install the mav comm package

$ cd $WORKSPACE/src
$ git clone https://github.com/PX4/mav_comm.git

Install the glog catkin package

$ cd $WORKSPACE/src
$ git clone https://github.com/ethz-asl/glog_catkin.git

Install the catkin simple package

$ cd $WORKSPACE/src
$ git clone https://github.com/catkin/catkin_simple.git

Install the ROS Quadrotor Simulator package

$ cd $WORKSPACE/src
$ git clone https://github.com/wilselby/ROS_quadrotor_simulator

Install rotors simulator

RotorS is a UAV gazebo simulator developed by the Autonomous Systems Laboratory at ETH Zurich. It provides some multirotor models such as the AscTec Hummingbird, the AscTec Pelican, or the AscTec Firefly, but the simulator is not limited for the use with these multicopters. There are simulated sensors such as an IMU, a generic odometry sensor, and the VI-Sensor, which can be mounted on the multirotor. This packages also contains some example controllers, basic worlds, a joystick interface, and example launch files. This package will serve as the foundation for the rest of the software development as it is already set-up to interface with the Gazebo simulator.

$ cd $WORKSPACE/src
$ git clone https://github.com/wilselby/rotors_simulator
$ cd rotors_simulator

Check for any missing dependencies. It may throw an error of missing dependency on [gflags_catkin] for package "glog_catkin", but this error does not seem to disrupt the compilation (catkin_make).

$ rosdep install --from-paths src --ignore-src --rosdistro indigo -y

Compile the workspace

$ cd $WORKSPACE
$ source devel/setup.bash
$ catkin_make

Install Xbox 360 Controller

Install the integrated Ubuntu Xbox driver

$ sudo apt-add-repository ppa:rael-gc/ubuntu-xboxdrv
$ sudo apt-get update && sudo apt-get install ubuntu-xboxdrv

Install the jstest-gtk package

$ sudo apt-get install jstest-gtk

The ROS wiki also contains a tutorial (http://wiki.ros.org/joy/Tutorials/ConfiguringALinuxJoystick) for configuring a joystick on Linux. Note that it may be necessary to update the joy node package parameters in the launch file based on the joystick’s assigned input value.

<param name="dev" type="string" value="/dev/input/js0" />

Model Verification

See https://www.wilselby.com/research/ros-integration/model-dynamics-sensors/ for a more detailed walk through

A command line tool check_urdf attempts to parse a file as a URDF description, and either prints a description of the resulting kinematic chain, or an error message. The first command creates a urdf file from the xacro file.

$ cd ros/catkin_ws/src/arducopter_slam/quad_description/urdf
$ rosrun xacro xacro.py kit_c.xacro -o /tmp/kit_c.urdf

Then run the urdf check:

$ cd /tmp/
$ check_urdf kit_c.urdf

The output will state the breakdown of the robot model

robot name is: quad
---------- Successfully Parsed XML ---------------
root Link: base_link has 5 child(ren)
    child(1):  base_link_inertia
    child(2):  rotor_0
    child(3):  rotor_1
    child(4):  rotor_2
    child(5):  rotor_3

This output can be visualized using the command:

$ urdf_to_graphiz kit_c.urdf

The quadrotor model can be visualized in Rviz by running the command

$ roslaunch quad_description quad_rviz.launch

The quad_world launch file is executed with the following command which displays the quadrotor model in Gazebo.

$ roslaunch quad_gazebo quad_world.launch

Manual Quadrotor Control

The quad_joystick_empty_world.launch file creates a simulation with the user providing desired attitude commands via the joystick to the attitude controllers on the quadrotor. A simple simulation of the quadrotor using only attitude controllers can be launched with the following command

$ roslaunch quad_gazebo quad_joystick_empty_world.launch

The position controller only publishes control commands if the user has entered “GPS mode” by pushing the “B” button by default on the Xbox controller. The “take off” mode, enabled by pushing the “A” button by default, sets the desired waypoint altitude to 1 meters. The “land” mode, enabled by pushing the “X” button by default, sets the desired waypoint altitude to 0 meters without modifying the x, y, or yaw values. A simulation with the quadrotor responding to position commands can be launched with the following command

$ roslaunch quad_gazebo quad_joystick_gps_empty_world.launch

Lastly, the package has a waypoint mode which allows the quadrotor to follow a pre-defined set of waypoints. The “waypoint mission” mode reads in a waypoint file that contains a series of waypoints and the time for them to be sent. First, the quadrotor must be in “GPS mode.” If enabled by pushing the “Y” button by default, the waypoint node will send each waypoint at the defined time. This allows users to develop and implement autonomous waypoint missions to navigate the quadrotor around the Gazebo world.

The waypoint files are stored in the quad_control/resource folder and are loaded in the waypoint_publisher_node. Each line in the waypoint file is a waypoint and has the following entries [time (s), x, y, z, yaw (deg)]. The kitchen world series of waypoint is loaded by default and can be tested by running the following command:

$ roslaunch quad_gazebo quad_joystick_gps_kinect_kitchen.launch

2D Mapping and Navigation

Once the quadrotor can reliably and stably navigate the environment based on a series of desired waypoints, the quadrotor system can be used to sense and comprehend it’s surrounding environment. A map is a representation of the environment where the quadrotor is operating. To operate in the map, the quadrotor needs to know its position in the map coordinate frame. Ultimately, the goal is to develop a system that allows the quadrotor to autonomously reach a desired goal state in the map.

A detailed walk through of the mapping process and utilization of Rviz for setting goals is available here: https://www.wilselby.com/research/ros-integration/2d-mapping-navigation/

In order to make an initial map of the environment, a series of waypoints was recorded. These waypoints maneuvered the quadrotor from its initial position outside the office complex, in and around several rooms, and returning back to the initial position. Note that the waypoint_publisher_node needs to be updated to read the wg_waypoints.txt file since this section uses the Willow Garage world by default.

$ roslaunch quad_2dnav quad_slam_laser_map.launch

Once the environment has been sufficiently mapped, the map can be saved for later use. The map is saved using the map_saver utility using the example code below.

$ rosrun map_server map_saver -f mymap

After creating the map, it is possible to use it for path planning and navigation. Ensure the correct map file name is being loaded in quad_2dnav.launch. First, the quadrotor must be in “GPS mode” as described above. Once the goal is set in RVIZ and the path created, the quadrotor will follow the path once “Autonomous mode” is enabled by pushing the right bumper by default. This can be tested by running the following command.

$ roslaunch quad_2dnav quad_2dnav.launch 

3D Mapping and Navigation

Ground-based robots are limited to 2D navigation due to their dynamics. However, since the quadrotor can also easily adjust its vertical position, 3D navigation can be implemented. Navigation in 3D enables the quadrotor more maneuverability to explore its environment, the ability to get a much more complete understanding of the environment, and also navigate the environment in more complex paths. This is especially useful when it comes to obstacle avoidance. To demonstrate 3D navigation, the kitchen world was used in Gazebo.

MoveIt! is state of the art software for mobile manipulation, incorporating the latest advances in motion planning, manipulation, 3D perception, kinematics, control and navigation. The MoveIt Setup Assistant is used to configure the quadrotor with the MoveIt! framework. This GUI generates the SRDF for the quadrotor was well as other necessary configuration files for use with MoveIt!. The MoveIt! Setup Assistant is launched using the following command.

$ roslaunch moveit_setup_assistant setup_assistant.launch

A detailed walk through of the configuration needed for MoveIt! is available here: https://www.wilselby.com/research/ros-integration/3d-mapping-navigation/

The 3D navigation simulation can be launched with the following command. To enable 3D autonomous navigation, first place the quadrotor into “GPS mode.” After the goal has been set and the path computed, the quadrotor can be set to follow the path by enabling the “3D Navigation mode” using the left bumper button by default.

$ roslaunch quad_3dnav quad_3dnav.launch

Authors

  • Wil Selby - Initial work -

License

This project is licensed under the MIT License

Acknowledgments and References

https://pixhawk.org/dev/ros/sitl

http://wiki.ros.org/indigo/Installation/Ubuntu

http://gazebosim.org/tutorials?tut=drcsim_install

http://dev.ardupilot.com/wiki/using-rosgazebo-simulator-with-sitl/

https://github.com/AurelienRoy/ardupilot_sitl_ros_tutorial/tree/master/scripts <<<<<<< HEAD

=======

c4536e1d33df0f07f3b313e1a617cdbec296ee22