ciaa/Hardware

Issues

• Include construction layout <EDU-CIAA-FPGA>

  #91 opened 4 years ago by juhas83
  0

• BOM Consolidation

  #87 opened 5 years ago by hjf
  1

• CIAA-Safety V1.0: U1 and U3 have no connection to GND on pin 2.

  #88 opened 4 years ago by nscotti
  0

• Not an issue: Would you want your project geographically re-annotated?

  #81 opened 5 years ago by BrianAtDocumentedDesigns
  0

• CIAA-ACC: There is no overvoltage protection on +5V jack.

  #84 opened 5 years ago by nscotti
  0

• CIAA-ACC: 3.3V to CAN IC U36 feeds through to VCCO_HR (Vadj) on FPGA banks.

  #83 opened 5 years ago by gguichal
  0

• The schematic v1.4 (pdf) was turned to the left and is not possible to find text on it

  #82 opened 5 years ago by rodrigomelo9
  1

• CIAA-ACC: JP4 resistor must be a 20K resistor.

  #76 opened 6 years ago by nscotti
  1

• Problemas en arranque cuando se usa el oscilador a XT (CIAA NXP y EDU CIAA NXP)

  #73 opened 7 years ago by jcecconi
  0

• RESET GPIO

  #79 opened 6 years ago by martinribelotta
  0

• CIAA-ACC: There is no 12V on FMC connector.

  #80 opened 6 years ago by nscotti
  0

• CIAA-ACC: SD card detect signal is necessary for booting from SD.

  #77 opened 7 years ago by nscotti
  0

• CIAA-FSL: EEPROM U1303 value is incorrect in JTAG sheet.

  #65 opened 9 years ago by nscotti
  0

• Reset al tocar battery holder

  #59 opened 10 years ago by mirkovich0
  3

• Digital Input LEDs and terminal blocks are mirrored

  #68 opened 9 years ago by pridolfi
  0

• CIAA-FSL: D301 is inverted on CEIBO 1.0 and CEIBO 1.1 schematics.

  #64 opened 9 years ago by nscotti
  0

• Cambiar footprint de D2.

  #63 opened 9 years ago by pridolfi
  1

• CIAA-FSL and CIAA-NXP: Input PTC should be replaced.

  #57 opened 10 years ago by nscotti
  2

• Cambiar footprint de TH10 TH3 TH4 TH5 TH6 TH7 TH9

  #62 opened 9 years ago by pridolfi
  0

• CR2032 battery shorts resistor R137

  #61 opened 9 years ago by elpablogomez
  2

• Flash qSPI (U20) package should be replaced.

  #60 opened 9 years ago by pridolfi
  0

• BOM actualizada silicio para temperatura con rango industrial (-40 a +85)

  #43 opened 10 years ago by jcecconi
  0

• BOM, falta detallar tensiones, corriente de ripple, tolerancia, rango temp, etc de algunos componentes

  #48 opened 10 years ago by jcecconi
  0

• EDU-CIAA-INTEL: Update BOM, add x100 and x1000 prices.

  #51 opened 10 years ago by pridolfi
  0

• EDU-CIAA-INTEL: PCB design enhancements

  #52 opened 10 years ago by pridolfi
  1

• CIAA-FSL: Test points

  #53 opened 10 years ago by nscotti
  0

• CIAA-NXP: DOUT0 ~ 3 LED indicators are inverted, should be corrected

  #55 opened 10 years ago by elpablogomez
  1

• CIAA-FSL: D1108 Digikey code

  #58 opened 10 years ago by nscotti
  0

• CIAA-NXP and EDU-CIAA-NXP: 15kOhm pull-down resistors are required for USB Host operation

  #56 opened 10 years ago by pridolfi
  1

• CIAA-NXP: Replace 32Mb Flash qSPI with 128Mb Flash qSPI in order to run the Linux kernel.

  #54 opened 10 years ago by pridolfi
  0

• CIAA-FSL: Entradas digitales

  #49 opened 10 years ago by nscotti
  0

• Jumpers para terminaciones en RS485 / CAN mediante pines de .1

  #47 opened 10 years ago by jcecconi
  1

• Change gate voltage for IRF820 mosfets to +5V instead of +24V. Remove CCRs.

  #41 opened 10 years ago by pridolfi
  1

• Change R107 package in order to use a 250mW resistor.

  #42 opened 10 years ago by pridolfi
  1

• MOSFET IRF820 son obsoletos, cambiar por FQT13N06L

  #44 opened 10 years ago by jcecconi
  1

• Pines de Expansion con soporte para módulo PoE

  #45 opened 10 years ago by jcecconi
  4

• CIAA-NXP: Replace 64Mb SDRAM with 128Mb SDRAM in order to run the Linux kernel.

  #50 opened 10 years ago by pridolfi
  0

• Update BOM according to #45, #44 and #42.

  #46 opened 10 years ago by pridolfi
  0

• CIAA-NXP: Invert pin numbers of battery holder.

  #39 opened 10 years ago by pridolfi
  1

• CIAA-NXP PCB: Agrandar PADs de pulsador de Reset, para mejor fijación mecánica

  #37 opened 10 years ago by jcecconi
  3

• CIAA-NXP PCB: Conectar pin 4 (Tab) del regulador a 3.3V para mejorar la disipación

  #38 opened 10 years ago by jcecconi
  2

• CIAA-NXP PCB: Change D6, D7 and D8 footprints to DO-214AA/SMB.

  #31 opened 10 years ago by pridolfi
  2

• CIAA-NXP: Try to rearrange terminal blocks.

  #40 opened 10 years ago by pridolfi
  2

• CIAA-NXP Remaining Tests: CAN.

  #30 opened 10 years ago by pridolfi
  1

• CIAA-NXP PCB: TRST there is not connection between FT2232H and microcontroller.Adjust R92 value and add Jumper

  #34 opened 11 years ago by pridolfi
  2

• CIAA-NXP PCB: RESET there is not connection between FT2232H and microcontroller.Adjust R90 / C69 values and add Jumper

  #36 opened 11 years ago by pridolfi
  1

• CIAA-NXP PCB: R92 (nTRTS) must be higher than 50K instead of 10K. Working fine with 100K

  #35 opened 11 years ago by jcecconi
  1

• CIAA-NXP PCB: R40 debe ser de 1/2W o usar 2 de 1/4W (1206)

  #33 opened 11 years ago by jcecconi
  0

• CIAA-NXP Remaining Tests: RS485.

  #29 opened 11 years ago by pridolfi
  1

• CIAA-NXP: Cambiar R34 del pin Di al Ro en U5 (MAX3072, RS485)

  #32 opened 11 years ago by jcecconi
  0