fieldOfView/Cura-ArcWelderPlugin

Issues

• Arc welder giving error code

  #40 opened 7 months ago by Heymap
  5

• Settings not always showing

  #37 opened a year ago by joryvd
  1

• Arc Conversion Performance

  #32 opened a year ago by Snoman002
  2

• Cura 5.5 engine plugins

  #36 opened a year ago by chrisnuzum
  2

• arc welder generates g3 with I=-0.000

  #33 opened a year ago by PaintOnBrush
  2

• "Out of Order" for Arcs, multiple artifacts and unnecissary moves

  #31 opened 2 years ago by Snoman002
  5

• Extruder goes bezirk

  #30 opened 2 years ago by j-snijder
  2

• Klipper question - Firmware Compensation

  #28 opened 2 years ago by derDoc81
  3

• Installed on version 5.1 of Cura on MacOS 12.5.1 but nothing happens to gcode

  #29 opened 2 years ago by deepcoder
  2

• Question: What's Needed for the Next SDK Major Version?

  #27 opened 3 years ago by edm00se
  3

• PlugIn "Arc Welder" will not start / load after update Cura 4.13.0b -> 4.13.0

  #26 opened 3 years ago by SpRiNgToIfEl
  12

• Arc Welder Cura extension causing badly placed skirt and odd movements at higher layers

  #25 opened 3 years ago by michaelmadden
  2

• Arc welder creating artifacts in Cura

  #18 opened 4 years ago by PhilBaz
  17

• ArcWelder default Maximum Arc Radius too large for 8-bit print controllers

  #24 opened 3 years ago by Risto-H
  3

• caught a bug: incorrect processing of the trajectory, risk of breaking the printer

  #23 opened 3 years ago by Goodfeat
  45

• Artifacts or settings issue?

  #20 opened 3 years ago by Dan-imal
  5

• Gcode results mutilate file

  #8 opened 3 years ago by seantapscott
  6

• Request: Better description as to where the option is turned on/off

  #11 opened 3 years ago by RFBomb
  2

• Request for version 1.1.1 in Cura Marketplace

  #13 opened 3 years ago by seantapscott
  4

• no arc movements in gcode

  #6 opened 3 years ago by dacentichka
  22

• Failed save to disk/removable drive on Linux (Mint 19)

  #22 opened 3 years ago by rburema
  1

• hard parameter limits prevent from using sensible values

  #12 opened 3 years ago by wohltat
  3

• Plugin for Cura LulzBot Edition

  #21 opened 4 years ago by b-morgan
  7

• Printer profile settings not registering

  #17 opened 4 years ago by Asterchades
  4

• Is it possible to enable it by default in a definitions file or only inside the plugin definition?

  #19 opened 4 years ago by brunoosti
  1

• Bug / Incompatability with 3.5.1 on Sidewinder X1

  #15 opened 4 years ago by ColinBathe
  16

• How To Run in Cura 4.9.0 ?

  #16 opened 4 years ago by 4Joe
  1

• No skirt or walls with arcwelder enabled

  #14 opened 4 years ago by pbezza
  5

• Plugin not available on Cura 4.8, because utf8 problem comes up

  #10 opened 4 years ago by unlimitopen
  4

• Charmap codec can't encode character \ufeff

  #9 opened 4 years ago by kvikindi
  0

• Plugin installed but no evidence of change

  #7 opened 4 years ago by 3dprintedmac
  2

• The plugin launch the conversion also when we save the project

  #2 opened 4 years ago by 5axes
  3