Issues
- 3
Introduce option for rotational axis
#92 opened by francotiveron - 3
Soft limit enable/disable
#63 opened by francotiveron - 3
- 3
Programable Jog Accel/Decel
#61 opened by francotiveron - 1
Black out disabled loadcell
#62 opened by francotiveron - 1
Screen change should clear moves/cues
#50 opened by francotiveron - 1
½ press and hold time to enter setup
#53 opened by francotiveron - 3
Change axis selection check boxes in moves and cues to larger selection buttons
#66 opened by francotiveron - 1
- 1
Auto Logout
#86 opened by francotiveron - 5
following error enable check box and value
#84 opened by francotiveron - 3
- 3
cues values beyond the max accel, vel or decel
#85 opened by francotiveron - 3
- 3
Color change for fault severity
#72 opened by francotiveron - 0
Relative moves don’t show negative values
#51 opened by francotiveron - 1
- 0
Cue time always reads zero
#59 opened by francotiveron - 0
If group is cleared, don’t enter group setup screen and software disable it
#65 opened by francotiveron - 0
- 0
It would be great if we can specify the color the axis changes based on the fault code. I am currently using your fault code function to show faults for all the limits, loadcells, position error, etc. if possible I would like to be able to specify different colors for different faults. Maybe the array can have 2 columns instead of 1 with the second column being a number to indicate red, yellow, orange, etc.
#82 opened by francotiveron - 0
Currently when we have a group tolerance fault, there is no way to clear it and realign the group except for clearing the group or manually jogging from the axis’ physical jog buttons. We would like a software option to realign a group. Currently if an axis goes over or under tolerance there is a unique fault for each. If the UI sees this fault we are thinking a button on the axis pops up that says realign. Upon pressing the button it would do a few things such has clear the axis’ group assignment, create a move absolute to a value I can create in twincat and display a popup window that says something like “press run to realign axis”. Once the axis is moved and the user presses the ok on the pop up it will reassign the axis to the group but not save any of the other group values that normally happen when assigning to a group
#81 opened by francotiveron - 0
It would be great to have a way to tune an axis from inside the UI. This could be button from inside the axis setup page that opens another page with the ability to create moves, set PID variables and watch a motion graph. I can provide a few variables for the graph but most important would be command velocity and actual velocity.
#80 opened by francotiveron - 0
We would also like the ability to be able to save/load a show/configuration file to USB or the harddrive. Not exactly sure how this would work since we do a lot of saving and variable writing in twincat as we use the UI, but it would be something useful to have.
#79 opened by francotiveron - 0
We have been asked for user specific axes. For example, user1 might be able to move axis 1-4 and user2 might only have access to axes 5-8. Not sure the best way to implement this so we would look for your suggestions
#78 opened by francotiveron - 0
Currently all presets run at the default axis speed which doesn’t seem to be enough capability. One thought is to have a preset call a cue which would allow for variable speed moves. This would mean changing the way a preset is written to creating a cue first then assigning the cue to a preset.
#77 opened by francotiveron - 0
Group realignment routine
#76 opened by francotiveron - 0
File saving
#75 opened by francotiveron - 0
Load based target
#74 opened by francotiveron - 0
Load cell filter
#73 opened by francotiveron - 0
Alternate units
#71 opened by francotiveron - 0
Larger cues for touch
#70 opened by francotiveron - 0
- 0
Alter language for autofollow
#68 opened by francotiveron - 0
Blank cue should start with first row
#60 opened by francotiveron - 0
Ability to change cue number
#58 opened by francotiveron - 0
Hold open brakes until cue completes
#57 opened by francotiveron - 0
Time based cues
#56 opened by francotiveron - 6
add an analog jog stick
#48 opened by francotiveron - 2
The clear button is a little small
#46 opened by francotiveron - 3
- 2
deadman enable button
#45 opened by francotiveron - 1
disable loadcells
#47 opened by francotiveron - 1
- 0
- 0
Group tolerance
#39 opened by francotiveron - 1
Fault reporting
#38 opened by francotiveron - 0
Add OK/Cancel Confirmation to 'Set New Position' Operation for Motors and Groups
#37 opened by francotiveron - 1
User Levels
#40 opened by francotiveron - 6
ability to save axis configs
#34 opened by pkelm1