/unitree_ros2

Primary LanguageC++BSD 3-Clause "New" or "Revised" LicenseBSD-3-Clause

ctrl+alt+T open the terminal, clone the repository: https://github.com/gabearod2/unitree_ros2

git clone https://github.com/gabearod2/unitree_ros2

where:

  • cyclonedds_ws: The workspace of Unitree ros2 package. The msg for Unitree robot are supplied in the subfolder cyclonedds_ws/unitree/unitree_go and cyclonedds_ ws/unitree/unitree_api.
  • example: The workspace of some examples.

Install Unitree ROS2 package

1. Dependencies

sudo apt install ros-humble-rmw-cyclonedds-cpp
sudo apt install ros-humble-rosidl-generator-dds-idl

2. Compile cyclone dds

The cyclonedds version of Unitree robot is 0.10.2. To communicate with Unitree robots using ROS2, it is necessary to change the dds implementation. See：https://docs.ros.org/en/foxy/Concepts/About-Different-Middleware-Vendors.html

Before compiling cyclonedds, please ensure that ros2 environment has NOT been sourced when starting the terminal. Otherwise, it may cause errors in compilation.

If "source/opt/ros/humble/setup. bash" has been added to the ~/.bashrc file when installing ROS2, it needs to be commented out:

sudo apt install gedit
sudo gedit ~/.bashrc
# source /opt/ros/humble/setup.bash

Compile cyclone-dds - edited

cd ~/workspaces/unitree_ros2/cyclonedds_ws/src
git clone https://github.com/ros2/rmw_cyclonedds -b humble
git clone https://github.com/eclipse-cyclonedds/cyclonedds -b releases/0.10.x 
cd ..
colcon build --packages-select cyclonedds #Compile cyclone-dds package

3. Compile unitree_go and unitree_api packages

After compiling cyclone-dds, ROS2 dependencies is required for compilation of the unitree_go and unitree_api packages. Therefore, before compiling, it is necessary to source the environment of ROS2.

source /opt/ros/humble/setup.bash # source ROS2 environment
colcon build # Compile all packages in the workspace

Connect to Unitree robot

1. Network configuration

Connect Unitree robot and the computer using Ethernet cable. Then, use ifconfig to view the network interface that the robot connected. For example, "enp3s0" in the following figure. image

Next, open the network settings, find the network interface that the robot connected.In IPv4 setting, change the IPv4 mode to manual, set the address to 192.168.123.99, and set the mask to 255.255.255.0. After completion, click apply and wait for the network to reconnect. image

Open setup.sh file.

sudo gedit ~/workspaces/unitree_ros2/setup.sh
#!/bin/bash
echo "Setup unitree ros2 environment"
source /opt/ros/humble/setup.bash
source $HOME/workspaces/unitree_ros2/cyclonedds_ws/install/setup.bash
export RMW_IMPLEMENTATION=rmw_cyclonedds_cpp
export CYCLONEDDS_URI='<CycloneDDS><Domain><General><Interfaces>
                            <NetworkInterface name="enp114s0" priority="default" multicast="default" />
                        </Interfaces></General></Domain></CycloneDDS>'

where "enp3s0" is the network interface name of unitree robot connected. Modify it to the corresponding network interface according to the actual situation.

Source the environment to setup the ROS2 support of Unitree robot:

source ~/workspaces/unitree_ros2/setup.sh

If you don't want to source the bash script every time when a new terminal opens, you can write the content of bash script into ~/.bashrc, but attention should be paid when there are multiple ROS environments coexisting in the system.

If your computer is not connected to the robot but you still want to use Unitree ROS2 for simulation and other functions, you can use the local loopback "lo" as the network interface.

source ~/unitree_ros2/setup_local.sh # use "lo" as the network interface

or

source ~/unitree_ros2/setup_default.sh # No network network interface specified

2. Connect and test

After completing the above configuration, it is recommended to restart the computer before conducting the test.

Ensure that the network of robot is connected correctly, open a terminal and input:

source ~/unitree_ros2/setup.sh
ros2 topic list

You can see the following topics: image

Input ros2 topic echo /sportmodestate，you can see the data of the topic as shown in the following figure： image

3. Examples

Open a terminal and input:

source ~/workspaces/unitree_ros2_rl_deploy/setup.sh
cd ~/unitree_ros2_rl_deploy/example
colcon build

After compilation, run in the terminal:

./install/unitree_ros2_example/bin/read_motion_state

You can see the robot status information output from the terminal:

[INFO] [1697525196.266174885] [motion_state_suber]: Position -- x: 0.567083; y: 0.213920; z: 0.052338; body height: 0.320000
[INFO] [1697525196.266230044] [motion_state_suber]: Velocity -- vx: -0.008966; vy: -0.001431; vz: -0.019455; yaw: -0.002131
[INFO] [1697525196.266282725] [motion_state_suber]: Foot position and velcity relative to body -- num: 0; x: 0.204149; y: -0.145194; z: -0.067804, vx: 0.002683; vy: 0.003745; vz: -0.010052
[INFO] [1697525196.266339057] [motion_state_suber]: Foot position and velcity relative to body -- num: 1; x: 0.204200; y: 0.145049; z: -0.068205, vx: -0.001954; vy: -0.003442; vz: -0.004828
[INFO] [1697525196.266392028] [motion_state_suber]: Foot position and velcity relative to body -- num: 2; x: -0.183385; y: -0.159294; z: -0.039468, vx: -0.000739; vy: -0.002028; vz: -0.004532
[INFO] [1697525196.266442766] [motion_state_suber]: Foot position and velcity relative to body -- num: 3; x: -0.182412; y: 0.159754; z: -0.039045, vx: -0.002803; vy: -0.001381; vz: -0.004794
[INFO] [1697525196.316189064] [motion_state_suber]: Gait state -- gait type: 1; raise height: 0.090000

Usage

State acquisition

1. Sportmode state

Sportmode state includes position, velcity, foot position, and other motion states of the robot. The acquisition of sportmode state can be achieved by subscribing "lf/sportmodestate" or "sportmodestate" topic, where "lf" represents low frequency. The msg of sportmodestate is defined as：

TimeSpec stamp // Time stamp
uint32 error_code //Error code
IMUState imu_state //IMU state
uint8 mode //Sport mode
/*
Sport mode
0. idle, default stand
1. balanceStand
2. pose
3. locomotion
4. reserve
5. lieDown
6. jointLock
7. damping
8. recoveryStand
9. reserve
10. sit
11. frontFlip
12. frontJump
13. frontPounc
*/
float32 progress //Is the dance action being executed?：0. dance false; 1. dance true
uint8 gait_type //Gait type
/*
Gait type
0.idle  
1.trot  
2.run  
3.climb stair  
4.forwardDownStair   
9.adjust
*/
float32 foot_raise_height 
float32[3] position 
float32 body_height
float32[3] velocity 
float32 yaw_speed
float32[4] range_obstacle
int16[4] foot_force 
float32[12] foot_position_body //foot positions in body frame
float32[12] foot_speed_body //foot velcities in body frame

For details, see：https://support.unitree.com/home/en/developer/sports_services.

Complete examples is in /example/src/read_motion_state.cpp. Run in the terminal:

./install/unitree_ros2_example/bin/read_motion_state

2. Low-level state

The low-level state includes motors states, power information, and other low level states. Low-level states can be obtained by subscribing "lf/lowstate" or "lowstate" topic. The lowstate msg is defined as:

uint8[2] head
uint8 level_flag
uint8 frame_reserve
uint32[2] sn
uint32[2] version
uint16 bandwidth
IMUState imu_state //IMU
MotorState[20] motor_state //Motor state
BmsState bms_state
int16[4] foot_force 
int16[4] foot_force_est
uint32 tick
uint8[40] wireless_remote
uint8 bit_flag
float32 adc_reel
int8 temperature_ntc1
int8 temperature_ntc2
float32 power_v 
float32 power_a 
uint16[4] fan_frequency 
uint32 reserve
uint32 crc

where MotorState are defined as：

uint8 mode        // Mode, 0x01 for control
float32 q         // Joint angle
float32 dq        // Joint velocity
float32 ddq       // Joint acceleration
float32 tau_est   // Estimated torque
float32 q_raw     //raw data of q
float32 dq_raw    //raw data of dq
float32 ddq_raw   //raw data of dq
int8 temperature 
uint32 lost
uint32[2] reserve

For details, see: https://support.unitree.com/home/en/developer/Basic_services Complete examples is in example/src/read_low_state.cpp.

3. Wireless controller

Wireless controller state can be obtained by subscribing "/wirelesscontroller" topic. The wirelesscontroller msg is defiened as:

float32 lx // left joystick x, range [-1.0~1.0]
float32 ly // left joystick y, range [-1.0~1.0]
float32 rx // right joystick x, range [-1.0~1.0]
float32 ry // right joystick y, range [-1.0~1.0]
uint16 keys // key values

For details, see: https://support.unitree.com/home/en/developer/Get_remote_control_status

Complete examples is in example/src/read_wireless_controller.cpp.

Robot control

1. Sportmode

Sportmode control is implemented by request/response mechanism. Sportmode control can be achieved by sending unitree_api::msg::Request msg to the "/api/sport/request" topic.

The Request msg for different sportmode interfaces can be obtained by the SportClient (/example/src/common/ros2_sport_client.cpp) class. For example, control the robot to reach a desired attitude:

 //Create a ros2 pubilsher 
rclcpp::Publisher<unitree_api::msg::Request>::SharedPtr req_puber = this->create_publisher<unitree_api::msg::Request>("/api/sport/request", 10);

SportClient sport_req; //Sportclient
unitree_api::msg::Request req; //Sportmode request msg
sport_req.Euler(req,roll,pitch,yaw); //Get Sportmode request msg from Sportclient 

req_puber->publish(req); // Publish request msg

For details about SportClient：https://support.unitree.com/home/en/developer/sports_services

Complete examples is in：example/src/sport_mode_ctrl.cpp. Run ./install/unitree_ros2_example/bin/sport_mode_ctrl in terminal. After 1 second of program startup, the robot will walk back and forth in the x direction.

2. Motor control

The torque, position and velocity control of motor can be implemented by subscribing "/lowcmd" topic and sending unitree_go::msg::LowCmd msg. LowCmd msg is defined as:

uint8[2] head
uint8 level_flag
uint8 frame_reserve
uint32[2] sn
uint32[2] version
uint16 bandwidth
MotorCmd[20] motor_cmd //motor command
BmsCmd bms_cmd
uint8[40] wireless_remote
uint8[12] led
uint8[2] fan
uint8 gpio
uint32 reserve
uint32 crc

where motor_cmd is defined as:

uint8 mode;  //Mode（Foc mode -> 0x01 ，stop mode -> 0x00)
float q;     //Target position (rad)
float dq;    //Target velocity (rad/s)
float tau;   //Target torque (N.M)
float kp;    
float kd;    
unsigned long reserve[3];

For details about low_cmd：https://support.unitree.com/home/en/developer/Basic_services

Complete examples is in：example/src/low_level_ctrl.cpo. Run ./install/unitree_ros2_example/bin/sport_mode_ctrl in terminal. The hip motor and calf motor of the RL leg will rotate to the corresponding joint angle.

Rviz

We can also use rviz to visualize Unitree robot data.The following is an example of visualizing robot lidar data:

Firstly, list all topics：

ros2 topic list

image

We can find the topic of lida：

utlidar/cloud

Then, echo frame_id of lidar：

ros2 topic echo --no-arr /utlidar/cloud

where frame_id: utlidar_lidar image

Finally, run rviz：

ros2 run rviz2 rviz2

Add Pointcloud topic: utlidar/cloud in rviz2 and modify Fixed frame to utlidar_lidar. Then, the lidar data is displayed in rviz2.

image image