CC's not working correctly
Opened this issue · 6 comments
Hi everybody,
1st of all thanks a lot gligli for your work, it's a huge gift you did for the P600 lovers ;-)
I've got an issue with CC's as it seems to work or notwork depending on the position of original pots on the computer.
Check this video, you'll see that the Cc22 works for Cutoff, then i move the real cutoff pot, and the CC22 doesnt work anymore, then i move the P600's Reso pot and the Cc22(cutoff) works again...
Somebody (Gligli?) could help?
May be using Nrpn? Dont'k know how to setup but the Behringer bcr2000 seems to be able to manage nrpn's.
As a last info, i had the exact same issue with an other Cc Controller.
This is 'normal' behavior and of technical origin. Nothing to worry about but yes, a little annoying.
Regards,
Maurits
Op 16 okt. 2016 om 18:52 heeft MattDiamonds notifications@github.com het volgende geschreven:
Hi everybody,
1st of all thanks a lot gligli for your work, it's a huge gift you did for the P600 lovers ;-)
I've got an issue with CC's as it seems to work or notwork depending on the position of original pots on the computer.
Check this video, you'll see that the Cc22 works for Cutoff, then i move the real cutoff pot, and the CC22 doesnt work anymore, then i move the P600's Reso pot and the Cc22(cutoff) works again...
Somebody (Gligli?) could help?
May be using Nrpn? Dont'k know how to setup but the Behringer bcr2000 seems to be able to manage nrpn's.As a last info, i had the exact same issue with an other Cc Controller.
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub, or mute the thread.
Is there an update for the sequencer? My gligli P600 doesn't work.
Sent from my iPhone
On 16 Oct 2016, at 18:07, Maurits Jonkergouw <notifications@github.commailto:notifications@github.com> wrote:
This is 'normal' behavior and of technical origin. Nothing to worry about but yes, a little annoying.
Regards,
Maurits
Op 16 okt. 2016 om 18:52 heeft MattDiamonds <notifications@github.commailto:notifications@github.com> het volgende geschreven:
Hi everybody,
1st of all thanks a lot gligli for your work, it's a huge gift you did for the P600 lovers ;-)
I've got an issue with CC's as it seems to work or notwork depending on the position of original pots on the computer.
Check this video, you'll see that the Cc22 works for Cutoff, then i move the real cutoff pot, and the CC22 doesnt work anymore, then i move the P600's Reso pot and the Cc22(cutoff) works again...
Somebody (Gligli?) could help?
May be using Nrpn? Dont'k know how to setup but the Behringer bcr2000 seems to be able to manage nrpn's.As a last info, i had the exact same issue with an other Cc Controller.
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub, or mute the thread.
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHubhttps://github.com//issues/87#issuecomment-254059430, or mute the threadhttps://github.com/notifications/unsubscribe-auth/AQftodtnXPJQsVzLu2RrCDqH_0hNIsjwks5q0lnlgaJpZM4KYBKf.
It may bave been fixed between 2.0 and 2.1rc3, but I'm not sure, it's been a while since I worked on p600fw code.
2.1rc3 also contains a step sequencer, downloads are there: http://gliglisynth.blogspot.fr/search/label/p600fw
@gligli thanks for your quick response, I did install the rc3 before asking ;-) And i'm sad the same issues occurs...
Do you think there's an other solution or i have to abandon the idea of controlling by midi?
My project is to make a 19' Rack of the P600, without keyboard & knobs, for the stage concerts i do. Just to play it in midi with my microkorg XL+ that has lot of custom CC possible to send.
... ;-)
Now I remember the last tweaked panel pot does parameter changes continuously to avoid stepping that would be caused by change detection. So it's effectively a technical choice.
As long as you don't edit a parameter by both MIDI and panel, it should work fine.
Thank you all guys for your replies, specially @gligli for all your efforts building this and remembering all the process to respond ;-)
Take care
MD