grblHAL/iMXRT1062

Issues

• Single Block switch ignored

  #87 opened 4 months ago by JasonTitcomb
  3

• Teensy4.1 and DM332T Drivers for a Basic CNC Machine

  #89 opened 4 months ago by silver2row
  2

• Error in GRBLHAL2000_map.h file

  #80 opened 9 months ago by zab-ig
  1

• Compilation problem after I formatted my macbook

  #85 opened a year ago by karoria
  7

• Not an issue: I want to know MODBUS implementation.

  #82 opened a year ago by karoria
  23

• $398=100 homing problems

  #83 opened a year ago by distebia
  1

• calo improvviso emissione fascio laser / pwm

  #81 opened a year ago by distebia
  6

• Using native USB host port as HID input for wireless keyboards

  #78 opened a year ago by karoria
  2

• Hello and I have Been Known to Misinterpret Ideas

  #76 opened a year ago by silver2row
  5

• COOLANT_MIST_PIN changing from pin 24 to any other available pin breaks communication with board after flashing successfully.

  #74 opened a year ago by karoria
  4

• valore ottimale planner $398

  #71 opened a year ago by distebia
  4

• aggiungere pin alla configurazione

  #69 opened a year ago by distebia
  13

• laser co2 + diodo

  #70 opened a year ago by distebia
  0

• I have run the compile both with Arduino IDE and PlatformIO with MCP3221 Enabled.

  #68 opened 2 years ago by sntlewis
  2

• How to add new pins and use them.

  #66 opened 2 years ago by ToRoCu
  17

• File not found : altpc.h

  #14 opened 2 years ago by Tiktiki
  22

• error: 'msSCSICapacity_t' does not name a type msSCSICapacity_t msCapacity;

  #15 opened 2 years ago by Tiktiki
  7

• Initial test of webui, ftp and SD

  #19 opened 2 years ago by karoria
  34

• Teensy 4.1 hangs at full buffer and trigger of emergency stop

  #21 opened 2 years ago by rcp1
  5

• Using the ethernet port

  #30 opened 2 years ago by mundsen
  1

• error:2 - Missing the expected G-code word value or numeric value format is not valid.

  #31 opened 2 years ago by Tiktiki
  36

• Z-probe support?

  #33 opened 2 years ago by mundsen
  4

• Teensy crashes with LITTLEFS

  #47 opened 2 years ago by BehemothTheKitten
  6

• LATHE Y to Z

  #56 opened 2 years ago by harryeveraert
  2

• RC PWM Spindle control

  #60 opened 2 years ago by 300bar
  2

• Question: Why is it an error to use a pin other than 12 or 13 for SPN PWM?

  #63 opened 2 years ago by ByronAP
  11

• BLTouch Servo Probe

  #59 opened 2 years ago by arda-min
  5

• Any chance to add one more axis to make it 6 axis?

  #37 opened 2 years ago by mac7988
  1

• Compile errors with latest code.

  #49 opened 2 years ago by andrewmarles
  44

• Limit switch/sensor issues and Homing

  #10 opened 2 years ago by phil-barrett
  4

• Bluetooth for Android sender

  #41 opened 2 years ago by mac7988
  6

• How to input Motor Fault signal?

  #51 opened 2 years ago by karoria
  5

• z-axis TLO and probing report with bCNC

  #50 opened 2 years ago by rschell
  4

• Coolant Flood/Mist pins reversed

  #48 opened 3 years ago by rschell
  2

• Teensy 4.1 hangs on custom board

  #34 opened 3 years ago by karoria
  3

• Can I add the 7th and 8th axis support.？

  #43 opened 3 years ago by pzh11001
  5

• USB host support

  #42 opened 3 years ago by karoria
  10

• Properly compile firmware for a dual-stepper-Y machine

  #46 opened 3 years ago by szaghi
  5

• Controller hardlocks after Invalid G-Code Command when using Ethernet connection

  #45 opened 3 years ago by Dietz0r
  3

• Spindle sync compile error

  #38 opened 3 years ago by LaurentLM
  1

• Swapping spindle PWM pin from 13 to 12 breaks comapilation

  #26 opened 3 years ago by karoria
  2

• UART communication mode not working for current version

  #28 opened 3 years ago by fireup924
  2

• unknown type name 'io_stream_properties_t

  #27 opened 3 years ago by fireup924
  2

• REQ: Add serial driver information for Serial8 on Teensy 4.1 as used in grblHAL2000 controller board

  #25 opened 3 years ago by 5ocworkshop
  4

• "Available driver options can be found here" link is broken for iMXRT1062 Driver

  #22 opened 3 years ago by 5ocworkshop
  1

• Teensy 4.1 hangs if N_AXIS >3

  #16 opened 3 years ago by Tiktiki
  1

• QEI_ENABLE causes build errors.

  #13 opened 3 years ago by phil-barrett
  2

• Teensy40 Unable to connect

  #12 opened 4 years ago by Bx3mE
  8

• Sub-par commenting Grbl-Hal sections of code

  #11 opened 4 years ago by AnthonyJQQ
  3

• Building with >3 Axes.

  #7 opened 4 years ago by phil-barrett
  19