/miniFOC

你还在为有刷电机的高噪声、低响应速度和低寿命而烦恼吗?这个项目是一个20块钱就能搞定的FOC无刷电机控制方案!This project is a FOC (Field Oriented Control) BLDC Motor control scheme that can be done for 3$!

Primary LanguageC++GNU Affero General Public License v3.0AGPL-3.0

LOGO

    Version  Build  License        English / 中文

    Are you still buying a DC brush motor drive module in about 2$? Are you still worried about the high noise in addition to the already low response speed and life? Allow me to present you our project, miniFOC---- a FOC brushless motor control scheme that can get you the most bang for your buck, for just 3$! miniFOC has a built-in torque closed-loop controller so that you can control a brushless motor with a 3-wire UART port. The software and hardware design are fully compliant with the AGPL-3.0 open source license.


Brief Introduction

    This open-source project aims to accomplish a FOC(Field Oriented Control) scheme that is operatable with minimum costs in China. The components selected in the example circuit are all manufactured in China. FOC possesses various advantages when it comes to controlling BLCD (Brushless Direct Current) motor; some of the benefits are as follows:

  1. FOC has no speed limit at all and can be accurately controlled at any speed
  2. FOC excels at its reversing performance, ensuring the smoothness of forward and reverse switching even when running at its highest speed
  3. FOC can also perform braking control in the form of energy recovery.
  4. FOC can achieve three closed-loop control of torque, speed, and position.
  5. FOC has significantly lower noise but much higher efficiency compared that of electric regulation

   Although FOC has many advantages, its large amount of calculation and complex principles requires an expensive controller, which made FOC unpopular. After half a year’s research and iteration, I deeply optimized the part of the code that implements mass calculations and re-selected its components to fit the domestic supply chain. I hope this open-source project can help domestic developers use BLDC motors with excellent performance and contribute to the open-source community.


Comparison Of Open Source Solutions

Open source solution miniFOC simpleFOC ODrive FpOC
Microcontroller GD32F130G6U6 ATmega328P STM32F405RGT6 FPGA
Driver chip EG2133 L6234 DRV8301 MP6540
PID loop frequency 30kHz (max) 830Hz (max) 8kHz (typical) 18kHz (typical)
Whether have current loop No No Yes Yes
Driving power 90W 120W 960W 90W
Cost price (approx.) 20¥ 100¥ 300¥ 150¥

    As can be seen from the table above, the scheme adopted by miniFOC can achieve high performance at low cost. At the same time, due to the re-selection according to the domestic supply chain, the selection of devices is not so limited, and there are many alternatives. amid the chip shortage in 2021, the cost of FOC still can be controlled at about 3$, which further proves the degree of cost optimization and the great potential of the project.


Performance Parameter

  • Input voltage range: 5V ~ 18V (you can modify the circuit according to the tutorial here to adapt to higher voltage).
  • Maximum driving current: 5A (you can modify the circuit according to the tutorial here to achieve greater driving current).
  • Detailed parameters of FOC: no current loop control, SVPWM (Space Vector Pulse Width Modulation) is adopted.
  • Communication parameters: UART baud rate is 115200, and Mid Capacity Data Transmit Protocol is used for data transmission.
  • Microcontroller parameters: Cortex-M3 core, 72MHz frequency, 32KB FLASH, 4KB SRAM.

Function Features

  • Using space vector pulse width modulation
  • Torque control without current sensor
  • Rotational speed closed loop control
  • Rotation angle closed loop control
  • Automatic phase sequence detection and correction

Development Environment

  • EDA Tool: EasyEDA (the standard free license is adopted, and there is no license dispute).
  • Compiler tool chain: gcc-arm-none-eabi 10-2020-q4-major
  • Programming tool: OpenOCD 0.11.0-1
  • Integrated development tools: CLion 2021.2.3 #212.5457.51
  • Software development tools: Qt 5.14.2 (MinGW 7.3.0 64bit)
  • Operating system and tool chain:
    • Win10 + MinGW + CLion + gcc-arm-none-eabi + OpenOCD
    • Ubuntu20.04 + make + cmake + gcc-arm-none-eabi + OpenOCD

Getting Started

Please refer to the wiki page of this project for getting started.
We also provide the domestic image address.
You can visit Github Page to learn about the usage of functions and variables in the code.
Note: Since the main development and deployment are carried out on Github, Gitee is only used as a domestic mirror warehouse to store the code, and there will be problems such as wiki and issue that are not updated in time. You can visit the Github source repository here.


Bugs & Feature Requests

Please report bugs and request features using the Issue Tracker and follow these request:

  1. Tab highlight when on different tab.
  2. Don’t let the update disappear if the window is not in focus.

License

The source code is released under a AGPL-3.0 License.

Affiliation:AcmeTech
Author: Zhu Yanzhen
Maintainer:YanzhenZhu, 2208213223@qq.com

    The product has been tested under Windows 10 and Ubuntu 18.04 and 20.04. This is research code, expect that it changes often and any fitness for a particular purpose is disclaimed.