Issues
- 11
Can you make this code non-blocking?
#116 opened by ham3dt - 0
- 0
Automatic Release Action
#129 opened by mandulaj - 1
How about a new release?
#128 opened by audaciousengineer - 13
- 2
CTs of higher rating
#127 opened by shayankhawar - 4
More than 4 pzem-004t
#124 opened by micheldufresne - 2
Set Address not working
#125 opened by lyinsushi - 10
Lamp cannot dim by TRIAC when connect with PZEM 004T
#123 opened by Kosaki01 - 6
Inconsisten Byte order in CRC check sum
#122 opened by mandulaj - 2
How do I reset the energy meter values?
#94 opened by loyolaphysics - 3
read value 0
#87 opened by zainurihasan - 2
Voltage measurement up to 500 volts
#113 opened by amir-eshaqy - 6
How to modify this code to only output certain values
#117 opened by ham3dt - 1
- 1
- 2
Is it possible to send one command to measure to all devices connected instead of sending multiple separated commands?
#120 opened by h4nsgd - 2
Check if module is connected
#119 opened by pvoncken - 5
ESP32 Hardware Serial doesn't work
#85 opened by Ncent-EP - 2
Pzem measuring wrong voltage values
#114 opened by Noor-H - 24
ESP32 Serial2 + 14 PZEM-004T Sensor Module
#92 opened by MFayH - 7
ESP32-WROOM-32 (DOIT ESP32 DEVKIT V1) + PZEM-004T-100A(V3.0) - all returned values are NaN
#100 opened by AlexGnatko - 7
when I try to upload, I get an error like this: no matching function for call to 'PZEM004Tv30::PZEM004Tv30(int, int)
#108 opened by mandulaj - 0
- 1
instantaneous value
#110 opened by DuCLeK65t - 1
Module PZEM-004T-100A-D-P
#111 opened by olonsoft - 0
Seeed Wio LTE
#109 opened by raymannnnnnnnnnn - 1
HOW TO RESET PZEM004TV3 ESP32?
#107 opened by margohaux - 1
Mycropyton
#106 opened by The-Kriz - 5
reset energy, set max power , read alarm flag.
#102 opened by iw2fvo - 2
Pzem-004t v3 + Esp32 DEVKITV1
#105 opened by M4carloz - 3
I can not read 3 pzem
#104 opened by sanluca - 4
Read Only Current
#103 opened by ChEfstr - 3
- 2
Current direction
#83 opened by jjtoard - 3
Connect 3 PZEM to 3 different serial ports
#84 opened by Pippozz - 2
Max value of current from the 100A Coil Transform at 100A circuit current.
#95 opened by sheminasalam - 2
Only read voltage
#99 opened by fadilhim - 6
Wrong value
#98 opened by ckvsoft - 1
Reading apparent energy
#91 opened by mohannad999 - 4
Invalid values
#93 opened by mlaci001 - 1
Example code using TTGO TCALL ESP32?
#97 opened by mandulaj - 9
- 2
Putting 3 PZEM modules in parallel does not work
#89 opened by sim0njo - 1
i use esp32 with hardware serial pin 16 and 17, i read sensor 3s/1time, when i read 10 times, it is miss about 4 times.
#86 opened by lequangthinhhaui - 1
LCDi2C to esp8266 - pzem004tv30
#88 opened by MikeLizter123 - 5
PZEM-004T on big electronics device
#82 opened by Albar0o0 - 0
Doesn't work on Arduino Micro
#81 opened by jagsilva - 5
Problems with multiple sensors
#78 opened by Monracloche - 1
I want Micropython Esp32 code Thank!
#77 opened by saisueb