qca/open-plc-utils

Issues

• bad mmv

  #156 opened 3 years ago by goRaspy
  5

• Unable to flash firmware: Minor Version Mismatch

  #138 opened 4 years ago by arkoz
  2

• qca7000 Firmware versions & Firmware parser development

  #137 opened 2 years ago by boraciner
  7

• Reading the duty cycle on control pilot

  #185 opened 4 months ago by KanteshwarBondla
  0

• When SLAC is in the Linked_ok state, the cpu_on status bit in INTR_CAUSE is set？

  #181 opened 8 months ago by IamTomChang
  1

• No response from red beet PLC unit on ethernet

  #183 opened 5 months ago by KanteshwarBondla
  1

• Cooperative mode with multiple PLC networks?

  #182 opened 6 months ago by netadair
  0

• G.hn support?

  #176 opened a year ago by laoshaw
  1

• Questions about the Local MAC and Host MAC of the QCA700x

  #180 opened 8 months ago by IamTomChang
  0

• struct cm_mnbc_sound_indicate is wrong

  #163 opened 2 years ago by vinicius-smartme
  1

• ls

  #179 opened a year ago by christianqueissner
  0

• QCA7500: Unable to flash firmware: "Failure (0xFF): Device refused request"

  #178 opened a year ago by AndersTrier
  1

• Can't List TPLink Devices

  #172 opened 2 years ago by jamstruth
  3

• fast charging scenerio with open-plc-utils?

  #177 opened a year ago by Fatih738
  0

• PLC: Wait for association

  #175 opened a year ago by christian-poljac
  1

• Changing The Prescaler Values on QCA7000

  #140 opened 4 years ago by maslanz
  1

• QCA7006 Comapitbility?

  #173 opened 2 years ago by mlind8
  2

• PLC Reboot

  #171 opened 2 years ago by Tifoso1979
  1

• Always getting CPU IRQ after the link is up

  #166 opened 2 years ago by boraciner
  0

• QCA7500

  #130 opened 5 years ago by alexi3
  3

• attenuation threshold vs SLAC strength

  #170 opened 2 years ago by janaranjanahl
  1

• Check Signal Noise and Tonemaps

  #168 opened 2 years ago by Tifoso1979
  3

• Unclear how to get rx/rx rates for local (nearest) node

  #169 opened 2 years ago by tomchiverton
  0

• Installation Problem

  #167 opened 2 years ago by Tifoso1979
  2

• Long link time >4.5 seconds < 25 seconds

  #165 opened 2 years ago by boraciner
  2

• SLAC folder don't compile

  #160 opened 2 years ago by amolina-chargevite
  1

• Use Ubuntu18.07LTS system, error“program: eth1: Address family not supported by protocol”

  #143 opened 4 years ago by zgb526642524
  3

• Function pev_cm_mnbc_sound setting wrong value for CNT field

  #164 opened 2 years ago by vinicius-smartme
  0

• How to use open-plc-utils to realize the entire DC fast charging process

  #153 opened 3 years ago by 1tianmaxingkong1
  1

• IP522CG V2/PL1200S Questions

  #132 opened 5 years ago by n3gwg
  2

• SERCOMM IP522CG v2

  #162 opened 3 years ago by n3gwg
  0

• Confused about CM_SET_KEY.CNF result field

  #161 opened 3 years ago by catphish
  3

• setting up qca device for SLAC 15118-3 pev or evse

  #157 opened 3 years ago by OSkrk
  3

• plctone + QCA7420 = "Read timeout or network error"

  #133 opened 4 years ago by aldennisa15
  4

• Chipset name is not reported correctly

  #151 opened 3 years ago by mhei
  2

• How do we get different versions of QCA7005 firmware and PIB files

  #155 opened 3 years ago by 1tianmaxingkong1
  2

• How do we get different versions of QCA7005 firmware and PIB files

  #154 opened 3 years ago by 1tianmaxingkong1
  0

• QCA7005 SPI response error

  #144 opened 3 years ago by 1tianmaxingkong1
  2

• NID Generation

  #149 opened 3 years ago by tropxy
  0

• Can't write firmware to QCA7420

  #135 opened 4 years ago by typhoon2099
  17

• QCA7450 PIB Write to scratch

  #148 opened 3 years ago by zgb526642524
  0

• MMTypes used in the demo and the MMTypes defined in the HPGP spec

  #147 opened 4 years ago by tropxy
  10

• plctone and int6ktone

  #146 opened 4 years ago by alexi3
  4

• Bin firmware

  #145 opened 4 years ago by rfg81
  4

• Cloning flash?

  #136 opened 4 years ago by typhoon2099
  2

• Settings (pre-scaler, etc) for more resilient, low-bandwith, long range PLC

  #126 opened 4 years ago by netadair
  1

• Does INSYS Powerline GP act as a HomePlug Ethernet Adapter?

  #139 opened 4 years ago by maslanz
  4

• qca7000 pib2xml

  #131 opened 5 years ago by zuoshouzeming
  0

• Avitar SW for QCA7000 firmware 1.2.5

  #129 opened 5 years ago by mrescude
  0

• QCA7500 psout reads incorrect values

  #128 opened 5 years ago by chris-vo
  0