Issues
- 2
Firmware for this yellow generic cheap ESC
#145 opened by batata004 - 0
- 1
Using SimonK with the Atmega 168P or Atmega328P
#147 opened by StoicaMad - 0
Redbrick 200a adding a 4th mosfet sandwich
#146 opened by Corypi - 0
- 0
How does Simonk modify the stop time after start-up stall failure? It needs to stop after 1 second
#143 opened by a146860 - 0
How to write tgy. Inc apfet bpfet cpfet inversion
#142 opened by a146860 - 3
Yellow ESC
#141 opened by diego0815 - 0
Disable the arming
#140 opened by kamilkamil1 - 3
e-skateboard brakes
#133 opened by youbobcat - 2
Asymmetric reversal response issue?
#116 opened by alspitz - 1
Red Brick 70A Motor stocks at 50% throttle
#138 opened by meddie77 - 0
hobbyking hk-b125a
#137 opened by jon1ik - 1
- 0
modular ESC
#135 opened by mkeyno - 1
Using SimonK with the Attiny84
#132 opened by Nxtv2 - 1
Can I replace Emax BlHeli 12A ESC fets with AO4407A p-fets and AO4430 n-fets ?
#131 opened by dushanEranga - 1
- 1
Disable all beeps? Possible?
#130 opened by infernusdomoso - 3
BS 40A - Motors "hammering"
#111 opened by ashankaei - 0
Issue with HVSK-40A (OPTO)
#127 opened by bricecgnt - 1
- 2
Variable Phase Advance
#95 opened by ahalekelly - 2
- 1
Problem with the Afro ESC USB Programming Tool
#117 opened by gurupras - 1
Max voltage with external 5V regulator
#104 opened by ehughwilliams - 1
- 1
Hobbywing Skywalker 30A
#108 opened by wiistriker - 1
DYS HV40A OPTO
#109 opened by AEROBATlCS - 3
no need for pulldown resistors.
#110 opened by rewolff - 1
Using these controllers as gimbal-style drivers?
#112 opened by jwatte-imvu - 1
How to backup?
#113 opened by Arise - 2
All n type bridge vs n and p type.
#115 opened by alnaufra - 2
PB6 & PB7 (OSC) use for XnFET & XpFET
#119 opened by Jonny89 - 1
- 1
Start-up Motor with High Load
#121 opened by radoof - 2
XXD 30A ESC Callibration Issue?
#89 opened by nicefellow1234 - 0
- 2
- 1
- 8
Dys SN20A with RC_PULS_REVERSE=1
#87 opened by fbyland - 6
- 6
- 25
Bad behavior with comp_pwm
#93 opened by Luisonson - 9
Red Brick 70A Changed Pins
#91 opened by ahalekelly - 1
Getting errors whilst compiling
#90 opened by ryanskidmore - 0
Cut fingers, broken blades
#88 opened by cimba007 - 2
comp_pwm too weak for active braking
#84 opened by dustin - 2
How to disable timeout?
#85 opened by vishnubob - 4
ZWT 12a (Blueseries 12a) - "copy" binaries?
#83 opened by swilkens