Issues
- 0
Spider 2.3 + TMC2240, Unable to write tmc spi 'stepper_x' register DRV_CONF
#161 opened by llambion72 - 0
- 5
- 0
我買的是 二 手 VORON 機 但想要重灌系統
#159 opened by wang098138 - 1
- 16
Spider 3.0 Stepper Stuttering on Power Up
#148 opened by Print3DWorld - 0
BTT Microprobe Causes board to stop working
#156 opened by markleaf131313 - 4
Spider 3 with TMC2209 V4.0 (fysetc) stepper drivers
#155 opened by ozzman39 - 1
- 1
Spider_v1.1_wiring.svg
#109 opened by dajosco - 3
Spider 3.0 sensorless homing
#146 opened by Gabriel121217 - 1
- 1
PC1 & PC2 in Spider 2.2 bad temps readings.
#119 opened by Darkgayo - 0
- 2
Spider v2.3; USB problems; no MCU id.
#150 opened by Fickert07 - 2
- 4
Fan's not working
#130 opened by whoisjako - 0
TMC stepper_x failed to init: Unable to write tmc spi 'stepper_x' register GLOBALSCALER, TMC5160 on Spider 2.3
#147 opened by Dual-Energy - 1
Water flow sensor
#145 opened by Cabinfourus - 5
Tmc2209 Unable to read tmc uart 'stepper_z
#144 opened by MakkeLeon2 - 5
Spider V2.2/klipper sensorless homing issue
#143 opened by Cabinfourus - 0
spider 2.3_YMAX vs BLTOUCH
#141 opened by leorpereira87 - 2
Spider 2.3 Running Very Hot
#139 opened by zigathustra - 1
Spider 3.0 documentation?
#137 opened by greenaar - 7
- 1
2.3 wont re-flash or upload bootloader
#134 opened by Garethgb - 0
Stepper motors not moving at all with Marlin
#136 opened by mattDuque - 0
- 2
Unable to use spider as USB to CAN bridge
#124 opened by kullwarrior - 0
Red led at fan1 is always on and Fan1 is always on
#133 opened by FaJoX - 1
How do i make a new Bootloader_FYSETC_SPIDER.hex file to upload to my controller
#121 opened by warhammertf - 5
[request] update RRF 3.3 -> 3.4
#131 opened by Moorviper - 0
FYSETC SPIDER V2.3 GPIO UART
#129 opened by akshaykaushik78 - 1
- 0
Unable to get canbus_uuid for SB CAN Toolhead.
#126 opened by Kravenovic - 1
Board doesn't work. 3.3v led doesn't turn on
#125 opened by daniel-sousa-me - 0
48V heater support?
#123 opened by andi-at-1 - 0
flash-sdcard.sh version mismatch
#122 opened by bpbastos - 5
- 2
TMC5160 Sensorless Homing Won't Work
#118 opened by kazooless - 1
Unable to read tmc uart 'stepper_x' register IFCNT Once the underlying issue is corrected
#117 opened by vogodesign - 0
BT0持续为高电平,无需跳帽默认进入DFU模式
#116 opened by T0nyr - 0
Setting I/O pin logical high/low problem
#115 opened by 4044ever - 1
[Documentation] Spider 2.2 pinout errata
#112 opened by numindast - 1
- 0
- 0
Marlin 2.x two Y and Z Motors
#110 opened by rainerschulte - 1
Spider wiring diagram error
#106 opened by Fuechsl - 0
spider v1.1 with power problem.
#105 opened by I-am-the-borg-queen79 - 1
Y+ endstop not firing on PA2
#103 opened by cyryllo