Pinned Repositories
16-bit-PIC-Microcontroller-to-Arduino-Multiple-Data-Transfer-using-UART
This Program is for both Transmitter side and Receiver side. This will transfer multiple variable value at a same time from 16 bit PIC24F to Arduino using UART Communication. The transmitter part will be interrupt by a timer of PIC24F. The receiver side will decode and separate all the received variable value.
Arduino-I2C-Analog-Data-Transfer
Arduino-UART-Communication-for-Multiple-Variable-Transfer
It will transfer multiple variable value at a same time and Receiver side can extract the different value individually.
Bit-wise-operation-in-8-bit-Microcontroller
Digital-I-O-in-PIC24F-16-bit-microcontroller
Digital-Switch-in-PIC24F-16-bit-microcontroller
LED-and-Switch-using-PIC24F-16-bit-microcontroller
Live-Weather-Display-OLED-Display
PWM-in-STM32
This program will show how we can generate multiple PWM wave from STM32 and vary the duty cycle of the PWM wave individually.
Timer-setup-in-PIC24F-16-bit-microcontroller
UttamBasu's Repositories
UttamBasu/Live-Weather-Display-OLED-Display
UttamBasu/amazon-freertos
IoT operating system for microcontrollers.
UttamBasu/atmega4808-air-quality-monitor-studio
This is the Atmel studio firmware associated with AN3403 Indoor Air Quality Monitor: Concept and Implementation.
UttamBasu/avr128da48-cnano-manchester-mplab-mcc
The repository contains two MPLAB® X projects: * *Manchester Encoder* and *Decoder*: using Core Independent Peripherals (CIPs) by following the interaction between TCB, USART, Event System, and CCL peripherals.
UttamBasu/avr128da48-phase-sequence-detection-of-ac-supply-mplab
This MPLAB® X Melody project supports the Application Note AN3607 Phase Sequence Detection of Three-Phase AC Supply and developed on AVR128DA48 Curiosity Nano Evaluation kit. This application uses ZCD and ADC peripherals of AVR DA family microcontroller.
UttamBasu/avr128db48-constant-current-driver-using-opamp-mplab-mcc
This MCC based MPLAB X IDE example shows how to use the Analog Signal Conditioning (OPAMP) peripheral to implement a constant-current driver using just one external resistor. The constant current amperage setting can be adjusted using firmware control.
UttamBasu/avr128db48-low-bom-mic-interface-using-opamp-mplab-mcc
This MCC based MPLAB X IDE example shows how to interface an electret microphone with a microcontroller (MCU) using the Analog Signal Conditioning (OPAMP). In addition to the microphone, only one resistor and one capacitor are required.
UttamBasu/avr128db48-opamp-as-regulated-power-supply-mplab-mcc
This MCC MPLAB® X example shows how to use the OPAMP as a regulated power supply for a second voltage domain.
UttamBasu/avr128db48-opamp-gain-and-offset-calibration-mplab-mcc
This MCC based MPLAB X example shows how to calibrate the gain and offset of the OPAMP when configured as a Programmable Gain Amplifier (PGA). The internal DAC and ADC are used to perform the calibration procedure. No external components are required.
UttamBasu/Azure-IoT-Heart-rate-monitor
Monitor heart rate using Azure IoT hub and web apps
UttamBasu/cayenne-docs
The Cayenne documentation system
UttamBasu/dt-overlay-pf-soc
Device Tree overlays and FIT image for Microchip PolarFire SOC
UttamBasu/Live-Speed-Display-using-Adruino-and-OLED-Display
UttamBasu/lnx4-class-material
Class material for the Microchip University LNX4 Class on EGT
UttamBasu/Master-Slave-connection-Between-two-Arduino-with-multiple-Sensors
UttamBasu/ml-same54-cult-wm8904-edgeimpulse-kws-demo
Keyword spotter demo with Edge Impulse and the SAME54 Curiosity Ultra board
UttamBasu/OLED-display-and-Multiple-Temperature-sensor-DHT11-with-Arduino-and-Serial-Monitor
UttamBasu/pic18f16q41-adcc-temp-sensor-mplab-mcc
This example will show how to use the Temperature Indicator Module and configure an ADCC to measure the device temperature
UttamBasu/pic18f16q41-cnano-opamp-demo-fw
This example demonstrates the different OPA peripheral modes of operation. This firmware is pre-loaded onto the Q41 Curiosity Nano development boards.
UttamBasu/pic18f16q41-curiosity-lpc-demo-code
This repository is the demo code for the PIC18F16Q41 device on the Low Pin Count (LPC) curiosity board.
UttamBasu/pic18f16q41-getting-started-opamp
This code example demonstrates the setup of the OPAMP module of the PIC18-Q41 family of devices using MPLAB Code Configurator (MCC).
UttamBasu/pic18f16q41-opamp-offset-correction
This code example demonstrates a method of compensating the input offset voltage error of the OPA module on the PIC18-Q41 family with temperature.
UttamBasu/pic18f47q10-crc-with-memory-scanner
This example describes the use of CRC peripheral with hardware-implemented memory scanner to generate checksum of program memory
UttamBasu/pic18f47q10-dac-waveform-generation
This example discusses how DAC peripherals from PICQ10, can be used to generate reference voltage and different signals.
UttamBasu/pic18f47q10-hlvd-monitoring-voltage
This example demonstrates using an HLVD module to quickly detect when the supply voltage of the microcontroller has decreased below the specified trip point or increased above the specified trip point
UttamBasu/pic18f57q43-analog-read-serial-write-mplab-mcc
This code example will use the ADC module to do an analog read and display on the USART port using a Terminal to see the values.
UttamBasu/pic18f57q43-hello-world-mplab-mcc
This example code hello world will setup ports and blink Led
UttamBasu/pic24f-dspic33c-easy-migration-demo
PIC24F/DSPIC33C Easy Code Migration Demo
UttamBasu/PIC32MZW1_refDesign_OOB
OOB demo for the PIC32MZW1 reference design board
UttamBasu/TUTORIALS
Files related to various tutorials on ThinkRobotics.in