ajn96/iSensor-SPI-Buffer

Issues

• Thank You!

  #39 opened 3 years ago by marshallmassengill
  0

• Ambiguous License

  #38 opened 3 years ago by xjzi
  1

• GPIO Configuration

  #37 opened 3 years ago by ajn96
  0

• Port SPI host/IMU interface code

  #36 opened 3 years ago by ajn96
  0

• Port HAL Init Code

  #35 opened 3 years ago by ajn96
  0

• Add DFU command bit

  #25 opened 4 years ago by ajn96
  2

• Add USB_SB mux support

  #33 opened 3 years ago by ajn96
  0

• Implement UART front end for CLI

  #34 opened 3 years ago by ajn96
  0

• Convert SD card driver from SPI to SDMMC

  #32 opened 3 years ago by ajn96
  0

• Use the unallocated pin on the USBC connector as a PPS input pin

  #28 opened 4 years ago by juchong
  4

• Add additional decoupling for the IMU

  #17 opened 4 years ago by juchong
  3

• Add a solder pad that disconnects the 24-pin connector VDD input from the buffer board

  #18 opened 4 years ago by juchong
  2

• Add support for automotive SPI protocol

  #31 opened 3 years ago by ajn96
  0

• Add user programmable button

  #24 opened 4 years ago by ajn96
  2

• Make the SD card accessible from the outside

  #21 opened 4 years ago by acloitre
  0

• Pass through VDDRTC (pin 24) to enable support for legacy IMUs

  #20 opened 4 years ago by juchong
  1

• Add test points to enable debugging the IMU-Buffer Board SPI Port

  #13 opened 3 years ago by juchong
  3

• Change processor from STM32F303 to STM32F722

  #26 opened 4 years ago by ajn96
  12

• Add an unpopulated connector for UART output (bypassing the USB port)

  #27 opened 4 years ago by juchong
  6

• Modify hardware to give buffer board reset control over IMU

  #7 opened 4 years ago by ajn96
  2

• Issue with timestamp over USB CLI stream

  #29 opened 4 years ago by ajn96
  4

• "Halted" USB port during steam causes watchdog reset

  #30 opened 4 years ago by ajn96
  0

• Investigate firmware compatibility with STM32F446

  #23 opened 4 years ago by ajn96
  10

• Add hardware power loss protection

  #8 opened 4 years ago by ajn96
  3

• Place interrupt vectors in core coupled memory

  #16 opened 4 years ago by ajn96
  2

• Occasional data corruption for high throughput USB stream

  #6 opened 4 years ago by ajn96
  2

• Add SD card data logging capability

  #4 opened 4 years ago by ajn96
  3

• Add frequency selection register for "PPS" signal

  #22 opened 4 years ago by ajn96
  2

• Change the SD card holder to be accessible without needing to remove the IMU

  #19 opened 4 years ago by juchong
  1

• Add Vdd measurements to output registers

  #14 opened 4 years ago by ajn96
  1

• Add watermark interrupt strobe functionality

  #15 opened 4 years ago by ajn96
  1

• TIMESTAMP_UPR Peak Value, when using 1Hz PPS Signal

  #11 opened 4 years ago by NevadaMark
  4

• Typo in Buffer Design Description

  #12 opened 4 years ago by NevadaMark
  1

• TIMESTAMP_UPR negative value?

  #9 opened 4 years ago by NevadaMark
  2

• Loss of PPS input question

  #10 opened 4 years ago by NevadaMark
  5

• Add support for buffer output via burst SPI

  #2 opened 4 years ago by ajn96
  1

• Add support for IMU burst data capture

  #1 opened 4 years ago by ajn96
  1

• Inconsistent IMU stall time under heavy SPI load

  #5 opened 4 years ago by ajn96
  1

• Add USB virtual serial port support

  #3 opened 5 years ago by ajn96
  1