PrintersForAnts/Micron

Issues

• Will there be a G2Z update for the R1 Beta?

  #132 opened 2 months ago by mookie-
  3

• Impossible to source the new belt spec in EU

  #133 opened 2 months ago by testack18
  2

• (R1 Beta) Z Drive Main body A & B - Chamfer for locating tabs

  #126 opened 5 months ago by cgauvrit
  1

• (R1 Beta) Z A & B Drives 20mm corner screws struggle to engage with brass inserts

  #128 opened 5 months ago by Foofinator94
  1

• (R1 Beta) Z drives belt alignment issues

  #124 opened 6 months ago by skuep
  3

• (R1 Beta) Issues/Suggestions on Belt Tensioning Mechanism

  #122 opened 6 months ago by skuep
  2

• (R1 Beta) 50mm Skirt Fan Option

  #123 opened 6 months ago by Walmtech
  0

• (R1 Beta) Enhancement/Fix XY joints cad the holes need adjustment for pin & add recesses for MR63-RS bearings

  #121 opened 6 months ago by shawnchr
  3

• (R1 beta) Z-Drive Main Body A/B STLs are inconsistent with respect to the shaft cutout

  #120 opened 6 months ago by skuep
  0

• R1 Klicky dock is a bit too low

  #117 opened 7 months ago by rsletten
  4

• New R1 spool holder foam #R1_beta_issues

  #118 opened 7 months ago by LordKillZone
  2

• Z idlers dont fit bigger 16T idler pulleys

  #116 opened 7 months ago by hartk1213
  1

• powge/formbot 64t pulleys dont fit Z drive

  #115 opened 7 months ago by hartk1213
  0

• Direct access to Micron_CAD_Assembly.step instead of zip file

  #109 opened 7 months ago by izanamisu
  3

• Gap between the "in part" support and the part itself is too wide on the 2 legs.

  #110 opened 7 months ago by BelgarionNL
  1

• Only `z_tensioner_a` inclunded in repo STLs

  #113 opened 7 months ago by DonutCables
  5

• KGLM-03 adaptation issues

  #107 opened 8 months ago by LeoD218
  2

• 220mm_m2_nut_adapter_rotated_x6(MICRON+).stl has incorrect orientation by default

  #102 opened a year ago by dderg
  0

• Cannot open the assembly step file in Solidworks

  #90 opened a year ago by Blue-RR
  1

• Missing some STL's for Stealthburner

  #92 opened a year ago by DaveyRance
  4

• Spacing bed extrusions for 180 size is not mentioned

  #87 opened a year ago by Toogo
  1

• Minimun layer height?

  #70 opened 2 years ago by ManuelPeiro
  1

• Revised A drive upper missing extrusion indexing tabs

  #89 opened 2 years ago by Outrider305
  0

• Affiliate kit links are both 404s

  #85 opened 2 years ago by thenickdude
  2

• Toolhead hits klicky dock

  #44 opened 3 years ago by moodytechz
  1

• Rail Stops: Key for Extrusion Alignment

  #32 opened 3 years ago by Finn2708
  1

• [a]_z_anchor_gantry_x1.stl orientation is wrong

  #47 opened 3 years ago by Finn2708
  1

• Missing STL's from folder: Micron/STLs/Gantry/Toolhead/

  #49 opened 3 years ago by moodytechz
  1

• M2 Nut adapter STL missing

  #45 opened 3 years ago by Finn2708
  1

• Ensure that 60t gears can be used

  #48 opened 3 years ago by grmocg
  1

• Panzerchain z_anchor_frame is non-functional

  #42 opened 3 years ago by grmocg
  1

• panzer chains missing top clip

  #41 opened 3 years ago by grmocg
  1

• Unclear which AB drive units to use

  #50 opened 3 years ago by grmocg
  1

• STLs/Gantry/Font_Idlers should probably be STLs/Gantry/Front_Idlers

  #51 opened 3 years ago by grmocg
  0

• Skirt trim and skirts have incorrect hole size for heat-inserts

  #36 opened 3 years ago by grmocg
  2

• make side-skirts have same mounting stuff as the f/r skirts.

  #39 opened 3 years ago by grmocg
  1

• Need additional holes in skirt/trim pieces to access z-drive screws

  #46 opened 3 years ago by grmocg
  2

• Wagos, Wagos everywhere?

  #43 opened 3 years ago by grmocg
  0

• Add slots to Z Belt Clamps

  #26 opened 3 years ago by Finn2708
  0

• Move PI back in the electronics mounting so the hinge can work in both ways

  #37 opened 3 years ago by grmocg
  1

• heatsets on carriage are annoying for some

  #40 opened 3 years ago by grmocg
  0

• Keys for Z Drives, AB Idlers and Frames

  #27 opened 3 years ago by Finn2708
  0

• stacked electronics mount allows octopus to touch motors when placed upside down

  #38 opened 3 years ago by grmocg
  1

• Motor cover STLs incompatible with longbois

  #35 opened 3 years ago by grmocg
  1

• need SSR mount for AC-bed configuration

  #34 opened 3 years ago by grmocg
  0

• Provide more clearance for USB-C for spider in flat mount.

  #33 opened 3 years ago by grmocg
  0

• Corners / Mounts for Deck Panel

  #28 opened 3 years ago by Finn2708
  0

• Protrusion for electronics mount to protect driver heatsinks

  #31 opened 3 years ago by Finn2708
  0

• Sliding / Pocket hinged doors

  #30 opened 3 years ago by Finn2708
  0

• Mount for mini-12864 display

  #29 opened 3 years ago by Finn2708
  0