makerbase-mks/MKS-TinyBee
MKS TinyBee is a mainboard for 3d printing, based on ESP32 module
C++GPL-3.0
Issues
- 5
Schematic for MKS tinybee
#107 opened by Elentriekerke - 0
Version 2.1 of Marlin has a serious flaw
#120 opened by noadgskill - 0
- 0
When one of the x and y endstops is triggered, the table and nozzle temperature appears as err.
#118 opened by scymz - 2
end stop temperature error
#108 opened by scymz - 1
Motors not working
#117 opened by imbence - 0
MKS TS35 for TinyBee
#116 opened by hotrododo - 1
- 1
Babystepping not working correctly.
#101 opened by JazzinSA - 3
Babystepping in real time.
#106 opened by Marcel67921 - 0
Reference Mosfet Q4, Q5 Of Fan0 and Fan1 ?
#115 opened by Beykerlun - 1
Marlin build in WiFi (supported in Bugfix 2.1.x?)
#102 opened by JazzinSA - 2
Layer shift when refreshing web-page
#111 opened by TjeerdvanDijk - 0
- 1
How to Control the Pins with the 74HC595 Shift Register?
#113 opened by SphaeroX - 0
USB-C connector doesn't work with USB-C cables
#112 opened by viernullvier - 5
This board is waste of money
#93 opened by enddDD - 0
AUTO_BED_LEVELING_BILINEAR with 3D touch
#110 opened by Marcel67921 - 11
- 5
Upgrading firmware Problems
#89 opened by ntsub - 2
MKS tinybee V 1.0 does not power on
#98 opened by ryan152159 - 1
Cr10 Stock Display Issues
#103 opened by ImNoahDev - 1
ABL
#105 opened by Marcel67921 - 1
Not working OLED ssd1306 display
#72 opened by Maksimius - 0
Will it work with ulticontroller?
#104 opened by acca84 - 1
No Screens seem to work on my TinyBee :( 2004 12684 - Reprap Discount and Full Graphic)
#74 opened by jaymcd - 2
MKS Tinybee reads wrong temperature
#99 opened by ducntq - 1
Wifi Support on Marlin bugfix 2.1.x
#100 opened by JazzinSA - 9
- 4
MKS tinybee web UI
#85 opened by irkzome117 - 1
Using TinyBee with external driver
#96 opened by alfeudm - 4
Extruder as z motor
#83 opened by enddDD - 0
Este es el archivo del código y todo lo relacionado con esa marca en el Marlin
#97 opened by Mauriciosanabria123 - 0
Repetier-Host and Tinybee board
#95 opened by booroondook-eng - 2
- 4
- 2
- 5
Nozzle heater intermitent error
#91 opened by meipsum - 4
- 2
- 1
Fans not working
#90 opened by Elentriekerke - 3
MKS tinybee board
#88 opened by ahmedhassan3298 - 1
Neopixel instead of 3dtouch
#86 opened by enddDD - 1
Continuous reboot of the TinyBee
#82 opened by andre1000 - 3
- 9
Error writing sd card using wifi
#75 opened by carlosm180 - 1
Поддержует Клиппер?
#79 opened by LastEKzail - 4
- 1
Temp error / USB error
#77 opened by carlosm180 - 2