tetrabiodistributed/project-tetra

Issues

• [Hardware] pushfit adapters to 22mm leaking in FDM

  #176 opened 3 years ago by Judoguy12
  6

• [Hardware] 3D printed adapters showing signs of leakage

  #181 opened 3 years ago by darraghbr
  5

• [Hardware] Moving to 12mm Push-fit And Photograph Test Setup

  #172 opened 3 years ago by Judoguy12
  16

• [Hardware] Pushfit expiratory valve needs a redesign to have a very low crack pressure

  #177 opened 3 years ago by mmroden
  0

• [Hardware] Document lung compliance differences in testing protocol

  #178 opened 3 years ago by mmroden
  0

• [Hardware] Build Progress Photos needed from UK Group

  #165 opened 4 years ago by mmroden
  4

• [Hardware] pushfit adapters to 22mm

  #168 opened 3 years ago by mmroden
  2

• [Hardware] pushfit to sensirion sensors

  #169 opened 3 years ago by mmroden
  0

• [Hardware] build up working tetra electronics with sensirion and pi board

  #170 opened 4 years ago by mmroden
  3

• [Hardware] Layout and design push fit Tetra system and enclosure

  #173 opened 3 years ago by darraghbr
  0

• [Hardware] build up working tetra electronics with sensirion and pi board in the UK

  #174 opened 3 years ago by mmroden
  0

• P-TET-000025 Inspiratory bias

  #121 opened 4 years ago by Burhan-Q
  4

• P-TET-000026 Expiratory bias

  #122 opened 4 years ago by Burhan-Q
  4

• Alpha Prototype rework

  #133 opened 4 years ago by Burhan-Q
  2

• P-TET-000005 & 06 NPT Hole (SLA) - Design Updates

  #105 opened 4 years ago by mechatroniks-git
  15

• P-TET-000018 Shutoff valve main body - Design Updates

  #104 opened 4 years ago by mechatroniks-git
  17

• Create P-TET-000032 Rear port adapters

  #123 opened 4 years ago by Burhan-Q
  2

• Get the Reqirements Document for Tetra

  #139 opened 4 years ago by Judoguy12
  3

• Write deliverables document for tetra

  #141 opened 4 years ago by Judoguy12
  1

• Write Tetra's Testing specification

  #140 opened 4 years ago by Judoguy12
  2

• Get the Mechanical test document

  #142 opened 4 years ago by Judoguy12
  4

• P-TET-000026 Dimension problems

  #153 opened 4 years ago by Judoguy12
  3

• P-TET-000032-0 No O-ring specified

  #154 opened 4 years ago by Judoguy12
  3

• [Hardware] Review drawings for push fit manifold and tube adaptors before release

  #163 opened 4 years ago by darraghbr
  9

• A-TET-001014 Expiratory Support mount Design Change

  #118 opened 4 years ago by Burhan-Q
  4

• Pi Hat design updates

  #129 opened 4 years ago by fpdotmonkey
  2

• Verify new pressure sensor assembly fits inside housing A-TET-001017

  #119 opened 4 years ago by Burhan-Q
  4

• P-TET-000033 Rear port cover

  #124 opened 4 years ago by Burhan-Q
  4

• Look into using different flow sensors

  #130 opened 4 years ago by fpdotmonkey
  2

• Explore making the MAF sensor a drop in sensirion replacement

  #131 opened 4 years ago by Judoguy12
  0

• Potential issue with noise on the ADC

  #150 opened 4 years ago by darraghbr
  2

• Missing item on Pi HAT BOM

  #159 opened 4 years ago by darraghbr
  3

• Add capacitor to PCB

  #134 opened 4 years ago by Judoguy12
  2

• Pi HAT PCB multiplexer resistors incorrect value

  #147 opened 4 years ago by darraghbr
  5

• Some plated through holes too close to traces on PCB

  #149 opened 4 years ago by darraghbr
  7

• Wire stubs found in PCB design

  #151 opened 4 years ago by darraghbr
  3

• I2C address selection pins not connected in accordance with application note

  #148 opened 4 years ago by darraghbr
  3

• Pi HAT PCB review

  #146 opened 4 years ago by darraghbr
  2

• add CI pipeline for autogenerating STL files

  #132 opened 4 years ago by capsulecorplab
  0

• P-TET-000020 Tetra Shutoff Valve Cap needs clearance

  #115 opened 4 years ago by mechatroniks-git
  11

• Review parts for Alpha prototype

  #120 opened 4 years ago by Burhan-Q
  6

• Organize tickets/ issues to different repos

  #107 opened 4 years ago by professor-nimrod
  5

• [DRAFT] Sprint-2 Alpha parts printing queue

  #110 opened 4 years ago by Burhan-Q
  11

• Sensirion control PCB adjustments

  #113 opened 4 years ago by Burhan-Q
  3

• A-TET-001004 Tetra PCB Assembly 5V Regulator Issue

  #112 opened 4 years ago by mechatroniks-git
  5

• P-TET-000001/2/3 Piping manifold design updates

  #108 opened 4 years ago by Burhan-Q
  6

• P-TET-000009 Front port cover - Design Updates

  #103 opened 4 years ago by mechatroniks-git
  7

• P-TET-000001/2/3 - Design Updates

  #106 opened 4 years ago by mechatroniks-git
  3

• A-TET-001010 - Drawing update

  #101 opened 4 years ago by mechatroniks-git
  4

• P-TET-000004 - Design update

  #102 opened 4 years ago by mechatroniks-git
  1