efabless/caravel_board

Issues

• GFMPW-1 read compare FAILED

  #111 opened 2 months ago by gonsolo
  1

• MPW5 *** read compare FAILED *** and Winbond SRAM not found

  #110 opened 4 months ago by hugodiasg
  1

• Setting register value

  #109 opened 4 months ago by Rimal12345
  0

• Caravel Rev 5B eval board: J6 (oscillator enable) & J2 (UART EN) label incorrect, misleading

  #108 opened 5 months ago by algofoogle
  0

• miniterm.py file for serial communication demo appears to be missing in the chipignite directory

  #107 opened 5 months ago by JamesTimothyMeech
  0

• uart mode confict for ftdi with UART_EN gpio pin

  #97 opened 10 months ago by jeffdi
  1

• Mismatch of GPIO mapping in defs.h and documentation

  #105 opened 8 months ago by IAmMarcelJung
  0

• add pdf schematic of the dev board

  #104 opened 9 months ago by mattvenn
  0

• Add libgcc to firmware examples Makefiles?

  #101 opened 9 months ago by mbalestrini
  0

• windows FTDI issues

  #95 opened 10 months ago by mattvenn
  0

• Mention J2 use for serial communication through USB on chipignite Readme

  #94 opened 10 months ago by mbalestrini
  1

• read compare error when flashing blink firmware for GF-MPW-0

  #82 opened a year ago by proppy
  3

• risc-v toolchain requirement should be documented

  #37 opened a year ago by proppy
  5

• Recent versions of RISC-V gcc require "zicsr" in the compile line.

  #87 opened a year ago by RTimothyEdwards
  2

• caravel procurement

  #69 opened 2 years ago by CarlFK
  3

• Board Issues Identified during bringup of CI2206 and GF180MCU

  #80 opened a year ago by azwefabless
  0

• dev-v5-M.2 component part numbers

  #77 opened 2 years ago by CarlFK
  0

• caravel nucleo board schematic should be searchable

  #70 opened 2 years ago by proppy
  0

• add 5V support for GFMPW-0 for caravel development board and nucleo hat

  #75 opened 2 years ago by jeffdi
  2

• Flexy pins socket on caravel development boards

  #67 opened 2 years ago by passant5
  0

• UART function definitions are missing

  #63 opened 2 years ago by abdullahyildiz
  9

• expose all mprj_io pins in the micropython HAL

  #66 opened 2 years ago by proppy
  2

• add nucleo micropython firmware to the repo

  #65 opened 2 years ago by proppy
  1

• Some FlexyPin socket pins are too close to JP6 and JP7 on Nucleo board

  #24 opened 2 years ago by abdullahyildiz
  1

• missing documentation for using gpio config for user project firmware

  #53 opened 2 years ago by jeffdi
  1

• add documentation regarding drive strength and limitations

  #60 opened 2 years ago by jeffdi
  0

• ValueError: incompatible .mpy file

  #20 opened 2 years ago by ayushman22git
  8

• all usb/serial connection should be documented

  #21 opened 2 years ago by proppy
  1

• RuntimeError: name too long after reflashing

  #22 opened 2 years ago by proppy
  2

• external power supply should be documented

  #23 opened 2 years ago by proppy
  1

• io_config control should give back control to the micropython interpreter

  #27 opened 2 years ago by proppy
  1

• GPIO0 missing

  #30 opened 2 years ago by thesourcerer8
  4

• a management pin below a user IO pin will not work (would need to change mgmt to low drive)

  #44 opened 2 years ago by jeffdi
  1

• seen IO_config passing when IO was in a intermediate voltage / high freq toggling

  #43 opened 2 years ago by jeffdi
  0

• difference when configuring IO using io_config vs standalone firmware

  #45 opened 2 years ago by jeffdi
  0

• difference when configuring IO using bit_bang vs housekeeping

  #46 opened 2 years ago by jeffdi
  0

• add firmware version to gpio_config_def.py

  #47 opened 2 years ago by jeffdi
  0

• io configuration depended on caravel hat mounted on nucleo

  #48 opened 2 years ago by jeffdi
  0

• power cycling Nucleo brings up voltage to 1.4V

  #41 opened 2 years ago by jeffdi
  0

• missing sanity check

  #49 opened 2 years ago by jeffdi
  0

• IO[37] is left in a bad state after io_config test completes

  #42 opened 2 years ago by jeffdi
  0

• add a check for users to verify IO configuration with a specific part

  #50 opened 2 years ago by jeffdi
  0

• unexplained behavior for IO toggling late

  #51 opened 2 years ago by jeffdi
  0

• cases where IO config will pass with different configuration for the same part

  #52 opened 2 years ago by jeffdi
  0

• filesystem on Nucleo gets corrupted and needs to be reflashed

  #54 opened 2 years ago by jeffdi
  0

• need hello world example using MPW-2 gpio config file

  #40 opened 2 years ago by jeffdi
  0

• found cases where Nucleo diagnostic incorrectly identifies gpio hold violations

  #39 opened 2 years ago by jeffdi
  0

• all possible led blinking patterns should be correctly documented

  #26 opened 2 years ago by proppy
  1

• Read Compare Failed

  #35 opened 2 years ago by Ankelih
  0

• Error during nucleo board reset

  #33 opened 2 years ago by mguthaus
  1