tetrabiodistributed/papr-print-files
This repository contains all of the files necessary to print components of the Tetra PAPR.
NOASSERTION
Issues
- 0
add a fuse holder to the battery pack
#237 opened by mmroden - 5
Investigate another 96mm fan
#207 opened by mmroden - 0
Complete 120mm design with 4 Stealth n100
#204 opened by mmroden - 0
Need a CPAP hose connector to 3m bayonet connector
#233 opened by mmroden - 0
Need a CPAP hose to a y connector
#234 opened by mmroden - 1
Investigate using papra as passive filtration device
#183 opened by mmroden - 3
- 0
Design clear vacuum-formable shell
#198 opened by mmroden - 0
find attachment points to vacuum-formable shell
#199 opened by mmroden - 0
Find straps to attach to attachment points
#200 opened by mmroden - 0
- 0
- 0
Figure out attachment for p100/n100 filter into the chin for exhalation source control
#196 opened by mmroden - 0
Test p100-based filter box design
#193 opened by mmroden - 0
- 1
SVG file for NATO filter gasket
#230 opened by Burhan-Q - 0
Allow for filters to be swapped out with out requiring complete disassembly of the box
#227 opened by mmroden - 0
- 3
- 3
- 4
The pressure tap model needs to get built
#220 opened by mmroden - 2
Investigate spacing between filter and fan for better filtration at higher flows
#180 opened by mmroden - 3
eFuse tripping when run at lower amperage
#167 opened by mechatroniks-git - 4
Investigate 30mm hosing to determine if that will relieve the battery life pressure
#170 opened by mmroden - 1
- 1
Create adaptor for activemask respirator
#202 opened by mmroden - 1
Better MOLLE attachment points
#214 opened by mmroden - 1
Figure out how to measure CO2 inside a mask
#203 opened by mmroden - 0
Split fan outlet into 3 pieces and test
#206 opened by mmroden - 1
3M respirator adapter not properly mounting
#192 opened by capsulecorplab - 1
STEP files belong in the STEP directory
#209 opened by mmroden - 2
- 0
Create adaptor for 7.5k respirators
#201 opened by mmroden - 0
Need gaskets for #205
#208 opened by mmroden - 1
fan box moves when run at full speed
#166 opened by mechatroniks-git - 0
Lower the weather shield for aesthetic reasons
#181 opened by mmroden - 1
Extend nut pockets in filter housing
#179 opened by mechatroniks-git - 1
Enlarge the nut pockets on the fanbox
#178 opened by mechatroniks-git - 1
minify the papr fanbox for roomba filters
#189 opened by mmroden - 2
investigate side port design
#185 opened by mmroden - 1
- 1
Weather guard stand broke
#168 opened by mechatroniks-git - 2
Aug 29 fanbox is not passing particle testing
#176 opened by mmroden - 1
may need washers to distribute force on water guard to prevent cracking on 29 aug 2021 build
#164 opened by mechatroniks-git - 1
hard to apply clamps when water guard is in place on 29 aug 2021 build
#163 opened by mechatroniks-git - 1
be sure to sand off edges of clip surfaces before attempting to attach clips
#165 opened by mechatroniks-git - 1
Add a slight flaring to the clips holding the filter holder to the filter box
#169 opened by mechatroniks-git - 0
MOLLE adaptors got deleted from the repo
#172 opened by mmroden - 0
Mask Gaskets got deleted from the repo
#173 opened by mmroden - 0
Assembly diagram for v5 of the papr-print-files
#175 opened by mmroden